Equinox Payments
8901 E. Raintree Dr., Suite 400, Scottsdale, AZ 85260, USA | Tel: +1.877.497.3726 | Fax: +1.480.551.7811 | www.EquinoxPayments.com
© 2013 Equinox Payments, LLC., all rights reserved. Equinox Payments and the Equinox Payments logo are registered trade-
marks of Equinox Payments, LLC. 940648-001E Rev. X 0x/13
INSTALLATION GUIDE
APOLLO AiO
The Apollo All-in-One (AiO) is ideal for merchants requiring a single device for
both merchant and consumer input. The AiO comes standard with a full-color
touchscreen, 384MB of total memory, a powerful 400MHz ARM11 32-bit
processor for fast transactions and the ability to support multiple applications.
INSTALLATION GUIDE
APOLLO AiO
940648-001E Rev A
940648-001E Rev. x
Easy access to
paper roll for
fast replacement
in seconds
Full-color
touchscreen
Prints logos, barcodes and
QR codes on receipts and
reports
Card reader features
“intelligent illumination”
Standard EMV card reader
Backlit, ADA-
style keypad
layout with
integrated PCI
PTS-approved
PIN Pad
+
+
+
+
+
+
WARNING
Only use the provided Equinox Payments A/C Power Adapt-
er. Non-compliant power adapters may damage the device.
Do not use if visibly damaged.
Do not expose to temperatures above 140 °F or 60 °C.
Do not disassemble.
Do not incinerate or crush.
Do not power ON terminal in a flammable atmosphere
(e.g., petrol station, chemical depot, etc.).
Keep out of reach of children or pets.
CAUTION
To reduce the risk of fire, use only No. 26 AWG or larger (e.g., 24
AWG) UL Listed or CSA Certified Telecommunication Line Cord.
SAFETY INFORMATION
The Apollo family of devices must be used within the operating
conditions, electrical supply requirements, environmental
conditions and connection requirements as specified below:
Power Supply: These devices must be connected to the
correct electrical supply. Connection to an inappropriate
supply may damage or destroy this device(s), thereby
invalidating its warranty(s).
Only operate these devices within the temperature range of
0 °C - 45 °C.
Hazardous Environments: These devices must NOT be
installed in locations where there is danger of explosion.
Usage: Under normal operating conditions, the distance to use
the device safely is approximately >=20 cm from the body.
COMPLIANCE
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
FCC Part 15
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
tion against harmful interference when the equipment is
operated in a commercial environment. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference in which case the user will
be required to correct the interference at his own expense.
The user is cautioned that changes or modifications not ex-
pressly approved by the party responsible for compliance
could void the user’s authority to operate this device.
UL/cUL Listed
RoHS Compliant
CB
PCI PED
FCC ID: NVA00008
FCC Part 68
This device complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the underside of this
device is a label that contains, among other information, a
product identifier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone
company.
A plug and jack used to connect this device to the premises
wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with
this device. It is designed to be connected to a compatible
modular jack that is also compliant.
The REN is used to determine the number of devices that may
be connected to a telephone line. Excessive RENs on a tele-
phone line may result in the devices not ringing in response to
an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as determined by the
total RENS, contact the local telephone company. The REN for
this device is part of the product identifier that has the format
US:AAAEQ##-TXXXX, where the digits represented by ## are
the REN without a decimal point (e.g., 03 is a REN of 0.3). If this
device causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinu-
ance of service may be required. But if advance notice isn’t
practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file
a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the
operation of this device. If this happens, the telephone compa-
ny will provide advance notice in order for you to make neces-
sary modifications to maintain uninterrupted service.
If trouble is experienced with this device, please contact
Equinox Payments at 1.877.497.3726 for repair or warran-
ty information. If this device is causing harm to the tele-
phone network, the telephone company may request that
you disconnect this device until the problem is resolved.
The user is not authorized to perform any service of this device.
Connection to party-line service is subject to state tariffs.
Contact the state public utility commission, public service
commission, or corporation commission for information.
DRAFT
