Epygi QX1000 Скачать руководство пользователя страница 16

Страница: 16 / 164

QX1000 Manual II: Administrator's Guide

Administrator’s Menus

QX1000; (SW Version 5.3.x)

The area

Receive Values

provides the following:

•

Receive Bytes

- number of received bytes.

•

Receive Packets

- number of received Ethernet

packets.

•

Receive Errors

- number of received packets

containing errors.

•

Receive Drop Errors

- number of received packets

that have been discarded.

•

Receive Overrun Errors

- number of received

overrun errors that occur when the receive buffer is
not large enough to hold all incoming packets. This
error usually appears due to a slow receiving
system.

•

Receive MultiCast Packets

- number of received

broadcast packets.

The area

Transmit Values

provides the following:

•

Transmit Bytes

- number of transmitted bytes

•

Transmit Packets

- number of transmitted Ethernet

packets.

•

Transmit Errors

- number of transmitted packets

containing errors.

•

Transmit Drop Errors

- number of transmitted

packets that have been discarded.

•

Transmit Carrier Errors

- number of transmit

carrier errors that occur due to a defective or lost
connection on the Ethernet link.

•

Transmit Collisions

- number of transfer errors that

occurred during a simultaneous packet transmission
from both sides.

Fig. II-18: Transfer Statistics Diagram Chart

To see the

Transfer Statistics Diagram Charts

, select the desired criteria and click

Save

to generate the corresponding chart and the table

showing the transfer statistics values (if enabled). The letters

(millions) and

(thousands) used in the legend of the displayed diagrams show the

total number of specified criteria. The

Reset Statistics

button is used to reset the chart and the table (if enabled).

Lines Status

The

QX1000 Status

Lines Status

page shows the current status of each IP lines including details of the attached extension. Since only one line of

information can be displayed at a time, the

IP Line

functional

buttons are used to navigate through the information regarding other lines.

The

Lines Status

table displayed for

lines includes a group of static and dynamic parameters. Static parameters are always displayed. Dynamic

parameters only appear when an event takes place on the extension.

Содержание QX1000





































































































































































Результаты поиска

Содержание QX1000

Отзывы:

Похожие инструкции для QX1000

Бренды по названию

Популярные бренды

Epygi QX1000, Руководство администратора

Результаты поиска

Содержание QX1000

Отзывы:

Похожие инструкции для QX1000

Бренды по названию

Популярные бренды