Epygi QX1000 Скачать руководство пользователя страница 138

Страница: 138 / 164

QX1000 Manual II: Administrator's Guide

Administrator’s Additional Feature

QX1000; (SW Version 5.3.x)

137

Administrator’s Additional Features

Incoming Call Blocking and Outgoing Call Blocking

The

Incoming Call Blocking

and

Outgoing Call Blocking

pages offer extended features for the administrator to activate incoming/outgoing call

blocking services for certain callers. The users cannot change this information.

For more information on the

Call Blocking Settings

pages, see the Incoming Call Blocking and Outgoing Call
Blocking chapters of the Extensions Users Guide - Manual
III.

The

Call Blocking

pages accessed from the

Caller ID

Based Services

table by clicking on the corresponding

address, gives the administrator the option to enable
blocking services which could not be disabled by the
users.

Along with the components seen by the user, an additional

Protect this entry

checkbox is available in the

Call

Blocking - Add Entry

pages for administrator access

only. With this checkbox selected, the user will be unable
to deactivate the blocking services configured by the
administrator.

Fig. II-237: Blocking Page for the Administrator

Содержание QX1000





































































































































































Результаты поиска

Содержание QX1000

Отзывы:

Похожие инструкции для QX1000

Бренды по названию

Популярные бренды

Epygi QX1000, Руководство администратора

Результаты поиска

Содержание QX1000

Отзывы:

Похожие инструкции для QX1000

Бренды по названию

Популярные бренды