Quadro4Li Manual II: Administrator's Guide
Administrator’s Menus
Quadro4Li; (SW Version 5.3.x)
98
7.
Enter a
Description
if needed.
8.
Enable the
Filter on Source / Modify Caller ID
checkbox, if the route functionality should be limited. This is dependent on the source caller
information.
9.
Enable the
Set Date/Time Period(s)
checkbox if a route
should be functional within certain time/date intervals.
10.
Enable the
Set Overall Calling Time Limit
checkbox if the total duration of the calls placed with the selected routing rule should be defined.
11.
Enable the
Set Tracing / Debug Options on This Rule
checkbox, if the tracing/debug options should be defined.
12.
Press
Next
.
13.
Select the user or attendant extension from the
Use Extension Settings
drop down list that the call will be placed on.
14.
Specify the
Destination Host
and
Port Number
,
Username
and
Password
if an
IP
or
IP-PSTN
call type has been selected. For the
IP-PSTN
call type, enable
Multiple Logons
if necessary. Enable the
Use RTP Proxy
checkbox if needed.
15.
Choose the Authentication and Accounting method from the
AAA Required
drop down list.
16.
Choose a
Fail Reason
from the corresponding drop down list.
17.
Configure
Transport Protocol for SIP messages
and
SIP Privacy
parameters as needed.
18.
Press the
Next
button.
19.
If the
Filter on Source / Modify Caller ID
checkbox has been previously enabled, fill in the
Source Number Pattern
into the corresponding
text field. Choose the needed value from the
Source Type
drop down list, as well as the
Number of Discarded Symbols
and
Prefix
values.
20.
Press the
Next
button.
21.
If
IP
has been selected on the previous step in the
Source Type
drop down list, then
Source
Host
should be inserted in the current page. If
ISDN
has been selected in the
Source Type
drop down list, then the ISDN port number should be selected here.
22.
If
the
Set Date/Time Period(s)
checkbox has been selected on the first page, pressing
Next
will open the
Date/Time Rules
page where route
validity should be defined.
23.
If the
Set Tracing / Debug Options on This Rule
checkbox has been selected on the first page, pressing
Nex
t will open the
Tracing/ Debug
Options
page where the tracing/debug options should be defined.
24.
If the
Set Overall Calling Time Limit
checkbox has been selected on the first page, pressing
Next
will open the
Routing Overall Calls
Limitation Settings
page where the total call duration for all calls can be configured over a specific time frame for each Call Routing Entry.
25.
If the
Class of Service
feature is enabled, assign the defined classes to the selected routing rule.
26.
Press the
Finish
button to establish a local route with the inserted settings.
To create a local AAA entry
1.
Click on the
Local AAA Table
link on the
Call Routing
page.
2.
Press the
Add
button on the
Local AAA Table
page.
3.
Choose the Authentication type.
4.
Enter the
Phone Number
,
Username
and
Password
or the
Authentication by PIN
depending on the selected Authentication type.
5.
Use the
Expiration Date and Time
checkbox to enable the expiration timeout.
6.
Select the
Expiration Date and Time
from the corresponding drop down lists.
7.
Press
Save
to apply these settings.
Allowed Characters and Wildcards
The following is the set of characters and wildcards allowed in the
Pattern
and
Inbound Caller Pattern
text fields of the Call Routing Wizard:
Characters:
0…9
a…z
A…Z
+ = $ ; / ~ _ - . & ( ) ' ! * ? {} , [ ]
Please Note:
The symbols
*
and
?
should be prefixed with a slash (\) if they are used as ordinary characters; otherwise the system will
interpret them as wildcards.
Please Note:
The symbols
!
,
{
,
}
,
[
,
]
,
-
and
,
are used to define a range of characters and cannot be used as ordinary characters.
Wildcards:
*
Any number of any characters
?
Any single character
{ }
A character or a string from the specified set of characters and strings.
The following control symbols are used to specify a set:
•
Use a comma (,) to separate the elements of a set.
Please Note:
No spaces are allowed within braces.
Example:
The pattern is
9{1,3,11,a}
.
Numbers matching the pattern are
91, 93 , 911, 9a.
•
Use a minus sign (-) to specify a range of characters. Each successive element of the range is obtained by increasing the
previous element (the element code) by one.
Example:
