Epson SureColor SC-F6000 Скачать руководство пользователя страница 57

Страница: 57 / 81

Problem Solver

What to Do When a Message Is Displayed

If the printer displays one of the messages shown below, refer to the solution listed and take the necessary steps.

Message

What to do

Chip Unit Error
Chip unit not recognized. Reattach
or replace.

❏

Reattach the chip unit. If the message persists, replace with a new chip unit.

“Replacing and Refilling Consumables” on page 48

❏

Condensation may have formed inside the tank. Store at room temperature for at
least 4 hours.

“Notes on Handling Ink Packs and Ink Tanks” on page 16

Chip Unit Error
Chip unit not recognized. Refill
after matching ink pack with label?

Attach the chip unit included with the specified genuine Epson ink pack.

You cannot use any genuine Epson ink packs other than the one specified.

“Options and Consumable Products” on page 64

Chip unit expended.
Replace chip unit.

The chip unit is nearing the end of its lifetime and needs to be replaced. Obtain a
replacement ink pack for the appropriate color as soon as possible.

“Options and Consumable Products” on page 64

“Notes on Handling Ink Packs and Ink Tanks” on page 16

F/W Install Error
Firmware update failed.
Restart the printer.

Turn the printer off, wait for a few minutes, and then turn on the printer again.

Use EPSON LFP Remote Panel 2 to re-attempt the update.

If this message appears on the LCD panel again, contact your dealer or Epson Support.

Command Error
Check print settings on RIP.

Press the

button and select

Job Cancel

to stop printing. Check to confirm that the

installed software RIP is compatible with your printer.

Paper Cut Error
Remove uncut paper.

After pressing the

button, pull out the paper and cut along the line of the failed cut

using scissors or a third-party cutter.

Pull out the end of the paper from the printer, and then press

Paper Size Error
Loaded paper is not supported
size.

The loaded paper width is not supported. Press the

button and remove the paper.

Paper for use in the printer must be at least 254 mm wide. Use paper that is at least 254 mm
wide.

Should this message be displayed with paper of a width that can be used in the printer,
you may be able to print if you select

Off

for

Paper Size Check

in the Setup menu.

“Setup menu” on page 40

SC-F6000 Series User’s Guide

Problem Solver

Содержание SureColor SC-F6000


















































































Результаты поиска

Содержание SureColor SC-F6000

Отзывы:

Похожие инструкции для SureColor SC-F6000

Бренды по названию

Популярные бренды

Epson SureColor SC-F6000, Руководство пользователя

Результаты поиска

Содержание SureColor SC-F6000

Отзывы:

Похожие инструкции для SureColor SC-F6000

Бренды по названию

Популярные бренды