Epson Stylus Pro 9000 Скачать руководство пользователя страница 35

Страница: 35 / 165

1-18

1-18

Handling Paper and Other Media

5. Push the paper set lever all the way down.

PRESS PAUSE BUTTON

appears on the control panel display.

6. Press the

Pause

button. The print head moves and the paper feeds into

printing position automatically.

READY

appears on the control panel.

(Even if you don’t press

Pause

, the paper and printer will move into

printing position automatically after 10 seconds.)

7. Print your page. After it is finished, the printed sheet stays in the printer.

8. To remove your print, hold it while pressing the

Paper Feed (–)

button.

Printing on Posterboard

You can print on heavy stock up to 28 × 40 inches (B1), such as EPSON
Posterboard Semigloss. Follow these instructions when you print on
posterboard or other media more than 19 mil (0.5 mm) thick.

1. Set the paper hammock to catch your printouts in front of the printer.

See page 1-21 for instructions. Extend the paper guides straight out in
front of the printer to keep the board from bending.

2. Press the

Paper Source

button repeatedly until the

Sheet

light

comes on.

3. Make sure the

Operate

light and

Pause

light are not flashing. Then

pull the paper set lever all the way up.

Caution

To avoid damaging the
printer, never move the
paper set lever while the

Operate

Pause

light

is flashing.

Note

You can’t run a cleaning
cycle when posterboard
is loaded for printing.

Содержание Stylus Pro 9000






































































































































































Результаты поиска

Содержание Stylus Pro 9000

Отзывы:

Похожие инструкции для Stylus Pro 9000

Бренды по названию

Популярные бренды

Epson Stylus Pro 9000, Руководство принтера

Результаты поиска

Содержание Stylus Pro 9000

Отзывы:

Похожие инструкции для Stylus Pro 9000

Бренды по названию

Популярные бренды