Epson Stylus Pro 9000 Скачать руководство пользователя страница 12

Страница: 12 / 165

Introduction

Using This

Printer Guide

This guide contains the following information:

Chapter 1 gives instructions for loading roll paper and cut sheets, printing
on various media, and using the paper hammock.

Chapter 2 explains how to monitor the printer’s status, respond to error
messages on the control panel, and configure printer settings.

Chapter 3 gives instructions for cleaning and aligning the print head,
replacing ink cartridges and the cutter blade, and cleaning and transporting
the printer.

Chapter 4 provides troubleshooting tips and solutions for problems
involving print quality, printer operation, and paper handling.

Chapter 5 provides the technical details on your printer, paper requirements,
and ink cartridges.

Appendix A gives instructions for installing an optional Ethernet interface
card.

Appendix B covers the installation and use of EPSON printer drivers and
utilities for Macintosh computers.

Appendix C covers the installation and use of EPSON printer drivers and
utilities for Windows computers.

An Index is included at the end of the book.

Содержание Stylus Pro 9000






































































































































































Результаты поиска

Содержание Stylus Pro 9000

Отзывы:

Похожие инструкции для Stylus Pro 9000

Бренды по названию

Популярные бренды

Epson Stylus Pro 9000, Руководство принтера

Результаты поиска

Содержание Stylus Pro 9000

Отзывы:

Похожие инструкции для Stylus Pro 9000

Бренды по названию

Популярные бренды