Epson Stylus Pro 7000 Series страница 87 Скачать руководство пользователя

Страница: 87 / 147

5-7

Monitoring the Printer

5-7

Checking Printer Status from a Macintosh

The Macintosh Status Monitor utility lets you check the levels of ink in your
printer and configure error messages and spooling features.

Follow these steps to check ink levels:

1. Click the utility button

on the Print or Page Setup dialog box. You

see the Utility menu:

2. Click the

EPSON StatusMonitor

icon.

SERVICE REQ
00000100

All lights
flashing

The waste ink system is full.

Contact EPSON to have the waste ink
system replaced.

TURN PWR OFF
AND ON

This message appears after
you clear a paper jam.

Turn the printer off and then on again.

UNABLE TO PRINT

You tried to print a test pattern
while an error condition was
present.

After 3 seconds the message
disappears. Press the

Pause

button

to exit SelecType mode. If the
message appears again, clear the
error before you print.

Error messages (continued)

Message

Light

Explanation

Response

Click to open the
Status Monitor
utility.

Содержание Stylus Pro 7000 Series




















































































































































Результаты поиска

Содержание Stylus Pro 7000 Series

Отзывы:

Похожие инструкции для Stylus Pro 7000 Series

Бренды по названию

Популярные бренды

Epson Stylus Pro 7000 Series, Руководство принтера

Результаты поиска

Содержание Stylus Pro 7000 Series

Отзывы:

Похожие инструкции для Stylus Pro 7000 Series

Бренды по названию

Популярные бренды