manualshive.com logo in svg

Epson Stylus Photo R290, Руководство по обслуживанию, Страница: 58 / 125

Поделиться
Скачать
Epson Stylus Photo R290 Скачать руководство пользователя страница 58

EPSON Stylus Photo R280/R285/R290

Revision B

Chapter 4 Disassembly/Assembly

4.2.1 Printer Cover (Removing Exterior Parts/Components)

58

4.2  Removing Exterior Parts/Components

4.2.1  Printer Cover

†

Parts/Components need to be removed in advance: Nothing

†

Removal procedure

1.

Pull out the left shaft and right shaft of the Printer Cover, and remove the 
Printer Cover.

Figure 4-9.  Removing the Printer Cover

4.2.2  Paper Support Assy

†

Parts/Components need to be removed in advance: Nothing

†

Removal procedure

1.

Open the Paper Support Assy.

2.

Disengage the right shaft of the Paper Support Assy from the bushing of the 
ASF Unit by pushing the bushing outward. Then remove the Paper Support 
Assy, disengaging the left shaft preventing the Edge Guide projection from 
hitting against the other parts.

Figure 4-10.  Removing the Paper Support Assy

Printer Cover

Shaft (right)

Shaft (left)

When reinstalling the Paper Support Assy, match the projection 
and hole of the Edge Guide, then attach the right shaft and the left 
shaft in that order. (Put the shafts at the front side in the bushing 
and then push them rearward.) After reinstalling, check that the 
Paper Support Assy moves smoothly.

Figure 4-11.  Reinstalling the Paper Support Assy

Push

Bushing of the ASF

Edge Guide 

Projection

 

:Shaft

Paper Support Assy

Convex Portion

Hole

1

2

: Shaft

Mounting Direction

(from front side to rear side)

Paper Support Assy

Содержание Stylus Photo R290






























































































































Отзывы:

Нет отзывов