Epson SC-F9300 series Скачать руководство пользователя страница 48

Страница: 48 / 146

Media Adjust

Use this menu in the following cases.

When doing a Head Alignment after Auto Feed
Adjustment for Easy Media Setup is complete

When media setting values for EMX files that were
downloaded are registered to the printer using
Epson Control Dashboard.

When the following conditions occur after
performing media adjustment.

❏

When banding can be seen in the print results
even after doing Auto Feed Adjustment
Select

Manual

, and then do

Feed Adjustment

Standard

❏

When the media type is the same but the width is
different

❏

When changing

Advanced Settings

after saving

media settings

Media Adjust (Auto Feed
Adjustment)

Adjust the media feed while printing a pattern, just
like in Auto Feed Adjustment that is done in Easy
Media Setup.

The approximate maximum length of the media
required to print the test pattern is given below.

Approx. 670 mm

Check that the printer is ready, and load the
media according to the actual usage conditions.

When using the Auto Take-up Reel Unit,
attach the media to the roll core.

“Loading media” on page 27

“Using the Auto Take-up Reel Unit” on

page 33

Press the

Menu

button.

The settings menu will be displayed.

Select in the order of

Media Setup

Customize

Settings

Media Adjust

Auto Feed

Adjustment

When you press

, auto adjust starts, and an

adjustment pattern is printed.

Wait until adjustment is complete.

Media Adjust (Manual)

Feed Adjustment

This menu is used when banding (horizontal banding,
tint unevenness, or stripes) is detected in printing
results.

You can do adjustments by selecting from

Standard

100mm Pattern

250mm Pattern

, or

500mm Pattern

Standard

Usually, this is selected.

100mm Pattern, 250mm Pattern, and 500mm
Pattern

Make a selection in the following cases.

❏

When banding can be seen in the print results
even after doing the adjustments for Standard

❏

When it is difficult to check due to bleeding ink,
etc., in the patterns for Standard

❏

When you want to print with accurate length

If, after doing

100mm Pattern

and

250mm Pattern

you feel that the media is still not completely aligned,
do a

500mm Pattern

The approximate maximum length of the media
required to print the test pattern is given below.

When performing

Standard

: Approximately 330 mm

When performing

100mm Pattern

: Approximately

570 mm

When performing

250mm Pattern

: Approximately

720 mm

SC-F9300 Series User's Guide

Basic Operations

Содержание SC-F9300 series



















































































































































Результаты поиска

Содержание SC-F9300 series

Отзывы:

Похожие инструкции для SC-F9300 series

Бренды по названию

Популярные бренды

Epson SC-F9300 series, Руководство пользователя

Результаты поиска

Содержание SC-F9300 series

Отзывы:

Похожие инструкции для SC-F9300 series

Бренды по названию

Популярные бренды