background image

4. History Data Details 

 

4.2 

USB History Data 

Table 4-2 shows the USB-related history data. 

Table 4-2    USB history data list 

History data 

Summary 

USB: VBUS overcurrent 

Detected VBUS overcurrent. 

USB: LS device 

Detected LS device connection. 

USB: FS device 

Detected FS device connection. 

USB: HS device 

Detected HS device connection. 

USB: storage device 

Detected storage device connection. 

USB: unsupported device 

Detected unsupported device connection. 

USB: more than 3 storage device 

Detected connection of 3 or more storage devices. 

USB: more than 4 hubs 

Detected connection of 4 or more USB hubs. 

USB: phase err 

Detected phase error. 

USB: CBW 

Issued CBW. 

USB: Data IN 

Issued Bulk IN (except CSW). 

USB: Data OUT 

Issued Bulk OUT (except CBW). 

USB: CSW 

Received CSW. 

USB: cleared STALL 

Issued request to clear STALL. 

USB: Mass Storage Reset 

Issued Mass Storage Reset (specified device reset). 

 

4.2.1 

USB: VBUS Overcurrent 

This history entry is recorded when an overcurrent is detected in the VBUS. If this history 
entry appears when an USB device is connected, the current drawn from the VBUS by the 
USB device may exceed the supply capacity. 

4.2.2 

USB: LS device 

This history entry is recorded when an LS (Low Speed) device is connected. This history 
entry is not recorded if connected via a USB hub. 

4.2.3 

USB: FS device 

This history entry is recorded when an FS (Full Speed) device is connected. FS devices 
include USB hubs recognized as FS. This history entry is not recorded if connected via a 
USB hub. 

4.2.4 

USB: HS device 

This history entry is recorded when an HS (High Speed) device is connected. HS devices 
include USB hubs recognized as HS. This history entry is not recorded if connected via a 
USB hub. 

S1R72U16 Development

 

EPSON 9 

Support Manual (Rev.2.00)

 

Содержание S1R72U16
























Отзывы: