manualshive.com logo in svg

Epson S1C33L26, Техническое руководство

Эпсон S1C33L26 - микроконтроллер высокой производительности для различных приложений. Для получения технической документации, скачайте бесплатное руководство пользователя на нашем сайте. Техническое руководство доступно для скачивания на manualshive.com. Полезная информация для успешной работы с продуктом.

Поделиться
Скачать
background image

15  16-BIT PWM TIMER (T16A5)

S1C33L26 TECHNICAL MANUAL

 

Seiko Epson Corporation 

15-15

T16A5 Ch.

x

 Comparator/Capture A Data Registers (T16A_CCA

x

)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

T16A5 Ch.

x

Comparator/
Capture A Data 
Register
(T16A_CCA

x

)

0x301186
0x301196

(16 bits)

D15–0 CCA[15:0] Compare/capture A data

CCA15 = MSB
CCA0 = LSB

0x0 to 0xffff

0x0 R/W

D[15:0]  CCA[15:0]: Compare/Capture A Data Bits

 

In comparator mode (CCAMD/ T16A_CCCTL

x

 register = 0)

 

Sets a compare A data, which will be compared with the counter value, through this register.

 

When CBUFEN/T16A_CTL

x

 register is set to 0, accessing to this register directly read/write from/to 

the compare A register.

 

When CBUFEN is set to 1, writing to this register loads the data to the compare A buffer. Compare data 
is always read from this register. The buffer contents are loaded into the compare A register when the 
counter is reset by the compare B signal.

 

The data set is compared with the counter data. When the counter reaches the comparison value set, 
the compare A signal is asserted and a cause of compare A interrupt occurs. Furthermore, the TOUT 
output waveform changes when TOUTAMD[1:0]/T16A_CCCTL

x

 register or TOUTBMD[1:0]/T16A_

CCCTL

x

 register is set to 0x2 or 0x1. These processes do not affect the counter data and the count up 

operation.

 

In capture mode (CCAMD = 1)

 

When the counter value is captured at the external trigger signal (T16A_ATMA_

x

 input) edge selected 

using  CAPATRG[1:0]/T16A_CCCTL

x

  register,  the  captured  value  is  loaded  to  this  register. At  the 

same time a capture A interrupt can be generated, thus the captured counter value can be read out in the 
interrupt handler.

T16A5 Ch.

x

 Comparator/Capture B Data Registers (T16A_CCB

x

)

Register name Address

Bit

Name

Function

Setting

Init. R/W

Remarks

T16A5 Ch.

x

Comparator/
Capture B Data 
Register
(T16A_CCB

x

)

0x301188
0x301198

(16 bits)

D15–0 CCB[15:0] Compare/capture B data

CCB15 = MSB
CCB0 = LSB

0x0 to 0xffff

0x0 R/W

D[15:0]  CCB[15:0]: Compare/Capture B Data Bits

 

In comparator mode (CCBMD/ T16A_CCCTL

x

 register = 0)

 

Sets a compare B data, which will be compared with the counter value, through this register.

 

When CBUFEN/T16A_CTL

x

 register is set to 0, accessing to this register directly read/write from/to 

the compare B register.

 

When CBUFEN is set to 1, writing to this register loads the data to the compare B buffer. Compare data 
is always read from this register. The buffer contents are loaded into the compare B register when the 
counter is reset by the compare B signal.

 

The data set is compared with the counter data. When the counter reaches the comparison value set, 
the compare B signal is asserted and a cause of compare B interrupt occurs. The counter is reset to 0. 
Furthermore, the TOUT output waveform changes when TOUTAMD[1:0]/T16A_CCCTL

x

 register or 

TOUTBMD[1:0]/T16A_CCCTL

x

 register is set to 0x3 or 0x1. 

 

In capture mode (CCBMD = 1)

 

When the counter value is captured at the external trigger signal (T16A_ATMB_

x

 input) edge selected 

using  CAPBTRG[1:0]/T16A_CCCTL

x

  register,  the  captured  value  is  loaded  to  this  register. At  the 

same time a capture B interrupt can be generated, thus the captured counter value can be read out in the 
interrupt handler.

Содержание S1C33L26



















































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C33L26

Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Бренд: Danfoss Страницы: 128
Vacon 100X series Installation, Technical And Maintenance Manual preview
100X series
Бренд: Vacon Страницы: 132
Zener SMARTSTART 6000 Networking Manual preview
SMARTSTART 6000
Бренд: Zener Страницы: 36
Zapi SMART CONSOLE Instructions preview
SMART CONSOLE
Бренд: Zapi Страницы: 5
Rain Bird ESP-RZXe Installation And Operation Manual preview
ESP-RZXe
Бренд: Rain Bird Страницы: 18
Mitsubishi A1SJ71E71N-B2 User Manual preview
A1SJ71E71N-B2
Бренд: Mitsubishi Страницы: 30
Epsolar eTracer ET4415BND Operation Manual preview
eTracer ET4415BND
Бренд: Epsolar Страницы: 44
Wavelength Electronics PTC5000 Datasheet And Operating Manual preview
PTC5000
Бренд: Wavelength Electronics Страницы: 17
Instrutech VGC301 User Manual preview
VGC301
Бренд: Instrutech Страницы: 42
Xvent ELEMENTAIR B-MARK I Operation And Installation Instructions Manual preview
ELEMENTAIR B-MARK I
Бренд: Xvent Страницы: 9
Vega VEGATOR 131 Operating Instructions Manual preview
VEGATOR 131
Бренд: Vega Страницы: 28
WATSON W91 Series Installation, Operation & Maintenance Instructions Manual preview
W91 Series
Бренд: WATSON Страницы: 16
Danfoss AME 56 Instructions Manual preview
AME 56
Бренд: Danfoss Страницы: 16
TDSi DIGIgarde PLUS User Manual preview
DIGIgarde PLUS
Бренд: TDSi Страницы: 71
Azbil AUR455 User Manual preview
AUR455
Бренд: Azbil Страницы: 68
Ltech LT-3900IR Manual preview
LT-3900IR
Бренд: Ltech Страницы: 2
Siro 40567 Instruction Manual preview
40567
Бренд: Siro Страницы: 2
ST STM32F469 Series User Manual preview
STM32F469 Series
Бренд: ST Страницы: 31

Бренды по названию

Популярные бренды

Загрузить еще бренды