Epson S1C17F13 Скачать руководство пользователя

Страница: 146 / 247

14 REAL-TIME CLOCK (RTC)

S1C17F13 TeChniCal Manual

Seiko epson Corporation

14-3

(Rev. 1.0)

Operations

14.4

Time Setting

14.4.1

Follow the sequence shown below to set time to RTC.
1. Set the following RTCCTL register bits:

- Write 0 to the RTCCTL.RTCRUN bit. (Stop RTC)
- RTCCTL.BCDMD bit

(Select binary/BCD mode)

- RTCCTL.RTC24H bit

(Select 24H/12H mode)

2. Check to see if the RTCCTL.RTCST bit = 0 (RTC is idle). If the RTCCTL.RTCST bit = 1 (RTC is operating),

wait until it is set to 0.

3. Write a time to the control bits listed below.

- RTCMIN.RTCSEC[6:0] bit

(Second)

- RTCMIN.RTCMIN[6:0] bit

(Minute)

- RTCHUR.RTCHUR[5:0] bit

(Hour)

- RTCHUR.AMPM bit

(AM/PM) (effective when RTCCTL.RTC24H bit = 1)

4. Write 1 to the interrupt flags in the RTCINTF register.

(Clear interrupt flags)

5. Write 1 to the interrupt enable bits in the RTCINTE register. (Enable interrupts)
6. Write 1 to the RTCCTL.RTCRUN bit. (Start RTC)

Write 0 to the

RTCCTL.RTCRUN bit

Write data to the RTCMIN and

RTCHUR registers

Write 1 to the

RTCCTL.RTCRUN bit

Yes

Counter setting

END

RTCCTL.RTCST = 0?

4.1.1 Counter Setting Procedure

Figure 14.

Notes:

•

An initial reset does not initialize the second/minute/hour counter values. Be sure to initialize

the counters via software.

•

Do not set the counters while the RTC is running (RTCCTL.RTCST bit = 1), as proper settings

to the counters cannot be guaranteed.

•

Counter values to be set must be within the effective range according to binary/BCD mode.

The counter will be undefined if a value out of the range is written.

•

Depending on the value set, an interrupt may occur immediately after starting the RTC.

•

The divider that generates F256 (256 Hz regulated clock) is reset when the RTC starts run-

ning (when 1 is written to the RTCCTL.RTCRUN bit). This affects the count operations of

other timers that use F256, as new F256 cycle begins from that point.

•

After an initial reset, the RTCCTL.RTCRUN bit is set to 0 and the RTC idles. The OSC1 oscil-

lator circuit is also idle. Therefore, resetting the IC suspends the RTC operation for the period

shown below.

RTC idle time = [#RESET = low period] + [Boot clock oscillation stabilization time] +

[Time until OSC1 is started] + [OSC1 oscillation stabilization time] +

[Time until RTC is restarted]

Содержание S1C17F13
























































































































































































































































Результаты поиска

Содержание S1C17F13

Отзывы:

Похожие инструкции для S1C17F13

Бренды по названию

Популярные бренды

Epson S1C17F13, Техническое руководство

Результаты поиска

Содержание S1C17F13

Отзывы:

Похожие инструкции для S1C17F13

Бренды по названию

Популярные бренды