manualshive.com logo in svg

Epson S1C17602, Техническое руководство

Эпсон S1C17602 - мощный микроконтроллер для различных устройств. Ознакомьтесь с техническим руководством, чтобы получить подробную информацию о функциях и возможностях этого устройства. Скачайте бесплатное руководство пользователя с нашего сайта, чтобы использовать все возможности Epson S1C17602.

Поделиться
Скачать
background image

13  16-BiT PWM TiMeRS (T16a2)

13-2

 

Seiko epson Corporation 

S1C17624/604/622/602/621 TeChniCal Manual

Comparator/capture block

 

The comparator/capture block provides a counter comparison function (comparator mode) and a count capture 
function (capture mode). When comparator mode is selected via software, the comparator/capture block can be 
used as a PWM waveform or clock generator. When capture mode is selected, this block can be used as a count 
capture unit for measuring external event periods/cycles. The comparator circuit generates the compare A and 
B signals that represent matching between compare A/B register values (set via software) and the counter value, 
and outputs the signals to the TOUT control circuit and the interrupt control circuit. The TOUT control circuit 
generates a PWM or other signal from the compare A and B signals and outputs it to the external TOUTA

x

 and 

TOUTB

x

 pins. The capture circuit loads the counter value to the capture A or B register using the CAPA

x

 or 

CAPB

x

 input signal that represents external events issued as a trigger. The interrupt control circuit outputs an 

interrupt signal to the interrupt controller (ITC) module according to the interrupt condition that has been set.

 

Comparator mode and capture mode cannot be used simultaneously in the same channel.

Combination of counter block channel and comparator/capture block channel

 

Generally, a counter block is connected to the comparator/capture block with the same channel number. The 
counter  block  and  the  comparator/capture  block  in  different  channels  can  also  be  connected. This  allows  a 

counter to use two or more comparator/capture blocks for expanding the comparison/capturing function from 
two systems to maximum four systems (details are described later).

notes:  •  The letter ‘

x

’ in register names refers to a channel number (0 or 1). 

 

  Example:  T16A_CTL

x

 register

 

   

 

Ch.0: T16A_CTL0 register

 

   

 

Ch.1: T16A_CTL1 register

 

•  The letter ‘

x

’ in EXCL

x

, CAPA

x

, CAPB

x

, TOUTA

x

, and TOUTB

x

 pins refers to a signal number 

(Ch.0 = 5, Ch.1 = 6).

 

  Ch.0: EXCL5, CAPA5, CAPB5, TOUTA5, TOUTB5

 

  Ch.1: EXCL6, CAPA6, CAPB6, TOUTA6, TOUTB6

T16a2 input/Output Pins

13.2  

Table 13.2.1 lists the input/output pins for the T16A2 module.

2.1  List of T16A2 Pins

Table 13.

Pin name

i/O

Qty

Function

EXCL5 

(for Ch.0)

EXCL6 

(for Ch.1)

I

2

External clock input pins
Inputs an external clock for the event counter function.

CAPA5, CAPB5 

(for Ch.0)

CAPA6, CAPB6 

(for Ch.1)

I

4

Counter-capture trigger signal input pins (effective in capture mode)
The  specified  edge  (falling  edge,  rising  edge,  or  both)  of  the  signal 
input  to  the  CAPA

x

  pin  captures  the  counter  data  into  the  capture  A 

register. The CAPB

x

 pin input signal captures the counter data into the 

capture B register.

TOUTA5, TOUTB5 (for Ch.0)
TOUTA6, TOUTB6 (for Ch.1)

O

4

Timer generating signal output pins (effective in comparator mode)
Each channel has two output pins and the signals generated in differ-
ent conditions can be output.

The T16A2 input/output pins (CAPA

x

, CAPB

x

, TOUTA

x

, and TOUTB

x

) are shared with I/O ports and are initially 

set as general purpose I/O port pins. The pin functions must be switched using the port function select bits to use the 
general purpose I/O port pins as T16A2 input/output pins. Also the external clock input pins (EXCL

x

) are shared 

with I/O ports. Setting the port to input mode enables it to be used as the T16A2 input pin with a general-purpose 
input function. For detailed information on pin function switching and port control, see the “I/O Ports (P)” chapter.

Count Clock

13.3  

The clock controller includes a clock source selector, dividers, and a gate circuit for controlling the count clock.  
The count clock can be controlled in each channel individually.

Содержание S1C17602

















































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S1C17602

Particle B Series Quick Start Manual preview
B Series
Бренд: Particle Страницы: 6
Tapeswitch C6 Technical Manual preview
C6
Бренд: Tapeswitch Страницы: 13
HANYOUNG NUX NP100 Manual preview
NP100
Бренд: HANYOUNG NUX Страницы: 36
HANYOUNG NUX HY Series Instruction Manual preview
HY Series
Бренд: HANYOUNG NUX Страницы: 4
MADRIX Nebula User Manual preview
Nebula
Бренд: MADRIX Страницы: 91
MADRIX Nebula Quick Start Manual preview
Nebula
Бренд: MADRIX Страницы: 40
YASKAWA MP Series Driver Manual preview
MP Series
Бренд: YASKAWA Страницы: 18
Kamstrup M-Bus Manual preview
M-Bus
Бренд: Kamstrup Страницы: 36
IBM MTM 2145-SV1 Hardware Installation Manual preview
MTM 2145-SV1
Бренд: IBM Страницы: 214
intech 21 OPLC-2100 Operation Manual preview
OPLC-2100
Бренд: intech 21 Страницы: 15
Xilinx ML410 User Manual preview
ML410
Бренд: Xilinx Страницы: 101
QSC TSC-101-G3 User Manual preview
TSC-101-G3
Бренд: QSC Страницы: 13
Holars AS H-TAG User Manual preview
H-TAG
Бренд: Holars AS Страницы: 15
Roth Touchline PL 2 Ch Installation Manual preview
Touchline PL 2 Ch
Бренд: Roth Страницы: 8
Samson TROVIS 5431 Mounting And Operating Instructions preview
TROVIS 5431
Бренд: Samson Страницы: 102
Madas RG/2MT X Series Technical Manual preview
RG/2MT X Series
Бренд: Madas Страницы: 28
Nidec Leroy-Somer R121 Installation And Maintenance Manual preview
Leroy-Somer R121
Бренд: Nidec Страницы: 16
Viessmann 5268 Servocontrol Manual preview
5268 Servocontrol
Бренд: Viessmann Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды