Epson PERFECTION V10 Скачать руководство пользователя

Страница: 53 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of AFL

4.5.8 Damper/Film Holder

1. Separate the AFL Upper Housing Assy/AFL Lower Housing Assy.

(4.5.1

Separation of AFL Upper Housing Assy/AFL Lower Housing Assy on page 46)

2. Push the Film Holder to release the lock, and open the Film Holder.

3. Turn over the AFL Upper Housing.

4. Remove the screw (C.B.P 3x8, 5-7 kgf.) that secures the Damper, and remove the

Damper and the Film Holder.

Figure 4-48. Removing the Damper

Film Holder

AFL Upper Housing

C.B.P. 3x8

Damper

AFL Upper Housing

Film Holder

Install the Damper/Film Holder following the steps below.

1. With the Film Holder wide open, insert the shaft of the Film

Holder into the hole of the AFL Upper Housing.

2. Insert the dowel of the Damper into the hole of the Film

Holder. Since the shape of the dowel and the hole is
rectangular, adjust the angle of the Damper as shown below so
that its dowel fit into the hole.

Shaft and
hole

AFL Upper Housing

Film Holder

AFL Upper Housing

Dowel of the

Damper

Содержание PERFECTION V10














































































Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды

Epson PERFECTION V10, Руководство по обслуживанию

Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды