Epson PERFECTION V10 Скачать руководство пользователя

Страница: 49 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of AFL

4. Remove the screw (C.B.P. 3x8, 5-7 kgf.cm.) that secures the AFL Inverter Board.

5. Disconnect CN2 connector, and remove the AFL Inverter Board.

6. Disengage the two hooks, and remove the AFL Inverter Board Cover from the

AFL Lower Housing.

Figure 4-39. Removing the AFL Inverter Board (2)

4.5.4 Lamp Assy

1. Separate the AFL Upper Housing Assy/AFL Lower Housing Assy.

(4.5.1 Separation of AFL Upper Housing Assy/AFL Lower Housing Assy on page
46)

2. Disconnect CN2 connector from the AFL Inverter Board.

(Figure 4-38 on page 48 )

3. Remove the two screws (C.B.P. 3x8, 5-7 kgf.cm.) that secure the Lamp Assy.

4. Lift up the Lamp Assy from the screws attached side to release the two tabs from

the slit of the AFL Lower Housing, and remove the Lamp Assy.

Figure 4-40. Removing the Lamp Assy

C.B.P. 3x8

CN2

AFL Inverter Board

Hook

AFL Inverter

Cover

C.B.P. 3x8

Slit and Tab

Lamp Assy

CN2

Lamp Assy

Содержание PERFECTION V10














































































Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды

Epson PERFECTION V10, Руководство по обслуживанию

Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды