Epson PERFECTION V10 Скачать руководство пользователя страница 12

Страница: 12 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

PRODUCT DESCRIPTION

Exterior Specifications

1.3 Exterior Specifications

Switches

Figure 1-3. Buttons and LED (Perfection V10/V100 Photo/V350 Photo)

Figure 1-4. Buttons and LED (Perfection V200 Photo)

Push Button

Note *1: Pressing the required buttons simultaneously can move the carriage. See

“Compulsory Carriage movement” (p22)

for the details.

*2: Perfection V10/V100 Photo/V350 Photo are powered On/Off by plugging/

unplugging the power code into/from a receptacle. Only Perfection V200 Photo can
be turned On/Off by the Start button, however, the button cannot turn it Off during
EPSON Scan is running.

Indicators

Note *1: Warm-up, scanning, initialization or other operation is in progress

*2: The LED does not flash red for some errors

(Option error, Command error)

LED

Table 1-3. Buttons Function

No.

Name

Functions

Start

Starts the EPSON Smart Panel.

Copy

Prints photos and makes prints from films.

Scan to E-Mail

Sends the scanned image by an e-mail.

Scan to PDF

Saves the scanned image as a PDF file.

Power ON

Start button.

Power OFF

Hold Start button down for three seconds or longer at power-on.

Table 1-4. LED and Scanner Status

LED

Status

Green

Ready

Flashing

Busy*

Red

Flashing

Error*

OFF

Power-off

Содержание PERFECTION V10














































































Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды

Epson PERFECTION V10, Руководство по обслуживанию

Результаты поиска

Содержание PERFECTION V10

Отзывы:

Похожие инструкции для PERFECTION V10

Бренды по названию

Популярные бренды