Epson LX-1170 Скачать руководство пользователя страница 70

Страница: 70 / 129

LX-300+/1170

Revision C

Disassembly and Assembly

Overview

4.1 Overview

This chapter explains the disassembly and assembly of LX-300+/1170.Read the precautions
below before disassembling and assembling the printer.

4.1.1 Precautions

See the precautions given under the handling “WARNING” and “CAUTION” in the
following column when disassembling or assembling the product.

4.1.2 Tools

The table below lists the tools recommended to use for disassembly and assembly and
adjustment. Use only tools specified here.

NOTE: All tools are available in market.

NOTE: Only component level repairing service requires oscilloscope.

W A R N I N G

Disconnect the power cable before disassembling or assembling
the printer.

Never touch the printer right after it finishes printing, for the
printhead is highly heated.

If you need to work on the printer with power applied, strictly
follow the instructions in this manual.

Always wear gloves for disassembly and reassembly to avoid
iujury from sharp metal edges.

To protect sensitive microprocessors and circuitry, use static
discharge equipment, such as anti-static wrist straps, when
accessing internal components.

C A U T I O N

Use only recommended tools for disassembling, assembling or
adjusting the printer.

Observe the specified torque when tightening screws.

Apply lubricants and adhesives as specified.

Make the specified adjustments when you disassemble the
printer.
(See Chapter 5 for details.)

When performing an adjustment, follow the method described in
this manual.

Table 4-1. Recommended Tools-1

Tools

Part No.

Needle-nose pliers

B740400100

Nipper

B740500100

Tweezers

B741000100

Soldering bit

B740200100

E ring holder #2.5

B740800400

+ driver No.2

B743800200

Box driver (opposite side distance: 7mm)

B741700200

Thickness gauge

B776702201

Table 4-2. Recommended Tools-2

Device

Specification

Multimeter

Oscilloscope

50MHz

Содержание LX-1170


































































































































Результаты поиска

Содержание LX-1170

Отзывы:

Бренды по названию

Популярные бренды

Epson LX-1170, Руководство по обслуживанию

Результаты поиска

Содержание LX-1170

Отзывы:

Бренды по названию

Популярные бренды