Epson LX-1170 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 129

background image

LX-300+/1170

Revision C

Operating Principles

Printer Mechanism

50

CARRIAGE HOME POSITION (HP) DETECTOR

The table below is the HP detector specifications.

HP detector detects the signal right after when the CR motor switches the phase.

2.2.2.1 High speed skip method

At no-printing area, the carriage moves at high speed compared to the normal carriage
speed at printing. This is called carriage control.

2.2.3 Ribbon Mechanism

2.2.3.1 Ink Ribbon Shifting Mechanism

Ink ribbon shifting mechanism: CR motor drives timing belt and the timing belt driven
pulley drives the ribbon shifting gears.

2.2.3.2 Color Ribbon Driving Mechanism (Option)

Color ribbon driving is only avilable for LX-300+.

Color ribbon driving mechanism: shifts the color ribbon up and down to change the
color area of the ribbon to be printed.

Color ribbon mechanism consists of the color shift (CS) motor, CS cam, ribbon detector,
CS lever assembly and color cartridge holder. Color ribbon is installed on the color
cartridge holder.

When CS motor revolves, 1) the pinion revolves CS cam, 2) the CS lever assembly on the
CS cam shifts the color cartridge holder up and down and 3) drives ribbon up and down.

Table 2-5. HP detector Specifications

Item

Specification

Method

Mechanical contact method

Switching rate

0.6 to 1.0 mA, 5 VD±5%

Switching mode

• out of HP: close

• within HP: open

Table 2-6. CS Motor Specifications

Item

Specification

Motor type

2-phase/48-pole PM stepping motor

Coil resistance

150

Ω

±5% (25°C, per 1 phase)

Control method

uni-polar rated voltage drive

Phase drive

2-2 phase

Drive voltage

36.75 ± 1.75 VDC

Consuming current

• Operating, peak current: 245 mA

• Non-operating:

20 mA

Drive frequency

500 pps

«
...
48
49
50
51
52
...
»

Содержание LX-1170


































































































































Отзывы:

Нет отзывов

Похожие инструкции для LX-1170

Бренд: NCR Страницы: 10

Бренд: SPRT Страницы: 28

DocuPrint C2200

Бренд: Xerox Страницы: 200

Бренд: Canon Страницы: 34

Бренд: Canon Страницы: 369

Бренд: Oki Страницы: 48

WorkCentre 7200 series

Бренд: Xerox Страницы: 12

Бренд: Rokit Страницы: 21

Бренд: Konica Minolta Страницы: 424

Бренд: Tandy Страницы: 83

Бренд: Shandong New Beiyang Information Technology Co. Страницы: 47

Бренд: TEC Страницы: 92

Бренд: Epson Страницы: 55

Бренд: Epson Страницы: 123

Бренд: Epson Страницы: 261

Бренд: Epson Страницы: 335

Бренд: Epson Страницы: 244

Бренд: Epson Страницы: 260

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды