Epson LX-1170 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 129

background image

LX-300+/1170

Revision C

PRODUCT DESCRIPTION

Operation

29

5.

Select setting value by LF/FF button.
Tear Off/ Bin LEDs and Paper Out LED show that menu’s value by status of On/Off/
Blink/2-Blinks. That value can be changed by pressing Tear Off/ Bin button and the
LEDs status of On/Off/Blink/2-Blinks will be changed as the button is pressed.

6.

When LF/FF button is pressed, the printer memorize the last setting value.

7.

Repeat (4) to (6).
The other items can be changed in the same manner.
The menu selection will return to the first menu after the last menu selection is over.

8.

Turn the printer off.
The setting is stored into non-volatile memory.

1.4.2.4 Bi-d. Adjustment

Bi-d. adjustment can be adjusted by users. Bi-d. adjustment method is as follows.

1.

Turning the printer on while pressing Pause switch. The guide to adjust Bi-d alignment
in this mode and the first alignment pattern will be printed.

2.

Select the most closely aligned number by pressing LF/FF (

↓

) and Load/Eject (

↑

)

switches.
Font LEDs and Pause LED show the pattern number which is selected at that time. The
selection is advanced one by one as the switch is pressed, and the combination of On/
Off/Blink of those three LEDs is also changed according to the selection.

Table 1-19. Setting Menu

Item

Setting / Value *2

Page length for tractor

3 inch, 3.5 inch, 4 inch, 5.5 inch, 6 inch, 7 inch, 8 inch, 8.5
inch, 11 inch, 70/6 inch, 12 inch, 14 inch, 17 inch

Skip over perforation

OFF, ON

Auto tear off

OFF, ON

Auto line feed

OFF, ON

Print direction

Bi-d., Uni-d., Auto

Software

ESC/P2, IBM 2390 Plus

0 slash

OFF, ON

High speed draft

OFF, ON

I/F mode

Auto, Parallel, Option

Auto I/F wait time

10 seconds, 30 seconds

Baud rate

19200BPS, 9600BPS, 4800BPS, 2400BPS, 1200BPS,
600BPS, 300BPS

Parity

None, Odd, Even, Ignore

Data length

8 bit, 7 bit

Parallel I/F bidirectional mode

OFF, ON

Packet mode

Auto, OFF

Character table

Software version
Italic, PC437, PC850, PC860, PC863, PC865, PC861,
BARASCII, Abicomp, Roman8, ISO Latin 1, PC858, ISO
8859-15

NLSP version
Italic, PC437, PC850, PC437, Greek, PC853, PC855,
PC852, PC857, PC864, PC866, PC869, MAZOWIA, Code
MJK, ISO 8859-7, ISO Latin 1T, Bulgaria, PC774, Estonia,
ISO 8859-2, PC 866 LAT., PC 866UKR, PC APTEC,
PC708, PC720, PCAR 864, PC860, PC865, PC861, PC863,
BRASCII, Abicomp, Roman8, ISO Latin 1, PC858, ISO
8859-15, PC771

International character set
for Italic table

Italic U.S.A., Italic France, Italic Germany, Italic, U.K.,
Italic Denmark 1, Italic Sweden, Italic Italy, Italic Spain 1

Manual feed wait time

1 second, 1.5 seconds, 2 seconds, 3 seconds

Buzzer

OFF, ON

Auto CR (IBM 2380 Plus)

*1

OFF, ON

IBM character table

*1

Table2, Table1

NOTE: *1: This setting is effective when IBM 2380 Plus emulation is selected.

NOTE: Setting with underline mean the standard factory settings.

NOTE: After W1xxxx Version.

Table 1-19. Setting Menu

Item

Setting / Value *2

«
...
27
28
29
30
31
...
»

Содержание LX-1170


































































































































Отзывы:

Нет отзывов

Похожие инструкции для LX-1170

Бренд: Oki Страницы: 17

Бренд: Oki Страницы: 12

Бренд: Oki Страницы: 30

Бренд: Oki Страницы: 391

Бренд: Oki Страницы: 2

Бренд: MakerBot Страницы: 48

Бренд: Wasp Страницы: 2

Бренд: OKIDATA Страницы: 44

Бренд: Savin Страницы: 4

Бренд: Hamlet Страницы: 76

4510B - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 10

Бренд: Ricoh Страницы: 284

Бренд: Dascom Страницы: 2

Бренд: Ricoh Страницы: 84

VersaUV LEF2-300

Бренд: Roland Страницы: 264

Бренд: Epson Страницы: 89

EasyFlow WorkForce 30

Бренд: Epson Страницы: 2

DS-50000 WorkForce DS-50000

Бренд: Epson Страницы: 91

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды