Display settings
You can adjust the following display settings:
Backlight:
Turns the backlight of the display on or off.
Contrast:
Adjusts the density of the fonts on the
display. (Value: -5 to +5)
Language:
Changes the language of the settings and
messages on the display.
inch:cm:
Selects the unit of measurement for length.
To adjust display settings, follow the steps below:
1. Press to turn on the product.
2. Press
+
.
3. Press
or
to highlight a setting, then
press
to select it.
4. Press
or
to select setting options, then
press
.
Setup
This product operates with batteries (not included) or
with an AC adapter (not included).
Inserting batteries
1. Remove the rear cover.
2. Insert 6 AA alkaline batteries.
Note:
If you need to install a tape cartridge, see “Inserting
a tape cartridge” below.
3. Replace the cover and snap it into place.
Optional AC adapter (APT0615Z1-1)
Warning:
Make sure to use AC adapter APT0615Z1-1 or
damage may occur.
1. Plug one end of the AC adapter into the product.
2. Plug the the other end of the AC adapter into the wall
outlet.
Inserting a tape cartridge
1. Remove any slack from the ink ribbon.
2. Remove the rear cover, if necessary.
3. Insert the tape cartridge and press it down firmly until
it snaps into place. If there is excess tape, feed the end
of the tape through the tape guide slot.
4. Replace the cover and snap it into place.
Preparing the tape
After inserting a tape cartridge, make sure to feed
some tape through the tape guide slot to position it
for printing.
1. Press to turn on the product.
2. Press
+
.
3. Press
to confirm.
4. Press the
Cut button to cut the tape.
Warning:
Do not press the
Cut button until the tape
stops moving or the tape cartridge may be damaged.
Removing a tape cartridge
1. Remove the rear cover.
2. Hold the cartridge by the tabs, and lift it straight up.
Language selection
1. Press to turn on the product.
2. Press
+
.
3. Press
or
to highlight
Language
, then
press
.
4. Press
or
to select your language, then
press
.
Creating labels
Use the character keys to enter text, then see below.
Changing the letter case
Press
to enter upper case or lower case for all letters
or
+ character for a single letter.
Deleting characters
Press
.
Deletes one character backward.
Deleting a label
1. Press
+
.
2. When a confirmation message appears, press
.
All entered text will be deleted.
Breaking lines
Press
.
Breaks the line from the character next to the cursor.
The line number is indicated on the display.
Note:
You can print a maximum of four lines of text. If you
try to exceed the maximum, appears and you will not be
able to print. Press
to delete the and print your label.
Adding punctuation
There are two groups of available punctuation marks.
: ; < > [ ] { }
1. Press
repeatedly to scroll through the
available marks.
2. Press
to select the desired mark.
" | _ ^ \ = - +
1. Press
+
, then press
repeatedly to scroll
through the available marks.
2. Press
to select the desired mark.
Adding symbols
1. Press
.
2. Press
or
to scroll through the
categories, then press
to select a category.
3. Press
or
to select a symbol, then press
.
Note:
To cancel and return to the previous menu,
press
.
Adding characters with an accent mark
If a character can include an accent mark, you can choose
it from a list indicated on the display.
1. Press
+ letter.
2. Press
.
A list of options appears on the display (e.g. ÈÉÊË).
3. Press
or
to select an item, then press
.
Creating sequentially numbered labels
1. Press
or
to move the cursor to a position
where you want to add a serial number, then
press
+
.
2. Enter a number for the first label, then press
.
The number increases by one when printing multiple
copies.
Saving labels
You can create and save up to 50 labels at a time.
To create multiple labels, type in your text, then press
+
or
+
to move to the next label (the label
number appears to the left of the text).
To print a label, press
+
or
+
to select the
label you want to print, then press .
Useful functions
Below are some common functions that will help you
customize your labels.
Changing the font size
1. Press
.
2. Press
or
to select a line layout, then
press
.
Note
: You can select a maximum of four lines of text.
“Equal” indicates the same font size for all lines.
Button names and functions
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
21
22
23
10
1. Power
2. Font
3. Font size
4. Frame
5. Font style
6. Settings
7. Character keys
8. Shift key
9. Caps lock
10. Accent
11. Space
12. Shift key
13. Select/Enter
14. Punctuation
15. Delete (
+
deletes all text)
16. Symbols
17. Special formats
18. Print copies
19. Preview
20. Cursor keys (
+
,
+
goes to
previous or next label)
21. Print (
+
feeds the tape)
22.
Cut button
23. Display
Turning the power off
Press to turn off the power. If using an AC adapter,
disconnect it from the wall outlet and the product.
If batteries are inserted, remove them only if the product
will not be used for a long period of time.
Display indicators
Indicators on the display show whether or not settings
are enabled.
1
2 3 4 5
6
7
8
9
10
11
1. Font size
2. Font width
3. Frame
4. Font style
5. Vertical text
6. Battery level
7. Accent mark options
8. Upper/lower case
9. Cursor (blinks to indicate current position)
10. Line number (appears when multiple lines exist)
Note:
You can print up to four lines of text.
11. Label number (you can save up to 50 labels)
3. Press
or
to select a font size, then
press
.
Tip:
The setting is indicated on the display.
Changing the font
1. Press
.
2. Press
or
to select a font, then
press
.
The font used for the entire line of text will change.
Available fonts
Changing the font style
1. Press
.
2. Press
or
to select a style, then
press
.
Note:
Styles applied to small or elaborate characters
may not print clearly.
Available styles
Shadow
Outline
S+O+I
Italic
S+I
S+O
Normal
Bold
B+I
O+I
Adding a frame
1. Press
.
2. Press
or
to scroll through the options,
then press
, or enter the frame number, to select
the desired frame.
Specifying the length of labels
1. Press
.
2. Press
or
to select
Label length
, then
press
.
3. Press
or
to select a value (up to 15
inches [40 cm]), then press
.
Tip:
Selecting
Auto
will adjust to the proper length
automatically.
Adjusting the space between characters
1. Press
.
2. Press
or
to select
Char. spacing
, then
press
.
3. Press
or
to select
Narrow
or
Wide
,
then press
.
Note:
The default setting (Narrow) is recommended.
Changing the font width
1. Press
.
2. Press
or
to select
Narrow
, then press
.
3. Repeat step 2.
Creating vertical text
1. Press
.
2. Press
or
to select
Vertical
, then
press
.
3. Press
or
to select
On
, then
press
.
Creating mirror image text
1. Press
.
2. Press
or
to select
Mirror print
, then
press
.
3. Press
or
to select
On
then
press
.
Creating special formats
Some of the functions in this section require the
format to be selected before entering text. If prompted,
press
to delete the current text and show the
Special label menu. Then type your label text.
Note:
To exit out of Special label mode, press
, press
or
to select
Exit
, then press
.
Creating an index tab label
1. Press
.
2. Press
or
to select a size, then press
.
3. Press
or
to select a value or enter
a number for the label length, then press
.
(Maximum length is 5.0 inches (12.5 cm).)
4. Enter text.
The same text entered in step 4 is automatically entered
in the next line.
Creating labels for cables
Flag labels
1. Press
.
2. Press
or
to select a flag type (
Flag:
Hori.
,
Flag:Vert.
or
Flag:Edge
), then press
.
3. Press
or
to select the length, then
press
. (Maximum length is 5.0 inches (12.5 cm).)
4. Enter text.
Note:
If you want to print more than one line of text, repeat
step 4 for each line (up to 4). When you are ready to print the
label, press .
Wrapped labels
1. Press
.
2. Press
or
to select
Wrap
, then
press
.
3. Press
or
to select a value or enter
a number for the label length, then press
.
(Maximum length is 5.0 inches (12.5 cm).)
4. Enter text.
Note:
If you want to print more than one line of text, repeat
step 4 for each line (up to 4). When you are ready to print the
label, press .
Creating a barcode label
1. Press
+
.
2. Press
or
to select a barcode format,
then press
.
3. Make any necessary settings (width, ratio, etc.), then
enter the code.
Supported barcode formats: CODE39, CODE128, ITF,
CODABAR, UPC-A, UPC-E, EAN-8, EAN-13
Enter barcodes according to their standards.
Check the created labels with your barcode reader to
make sure they can be read correctly.
Printing labels
Previewing a label
Press
.
Entered text scrolls across the display.
Note:
Only the text and the length of the label can be
previewed. The actual print image will not show on the
display.
Printing a label
1. Press .
The length of the label and the number of copies
shows on the display while the label prints.
2. When printing stops, press the
Cut button.
Warning:
Do not press the
Cut button until the tape
stops moving or the tape cartridge may be damaged.
Printing multiple copies
1. Press
.
2. At the next screen, press the number keys or the
or
buttons to enter the number of
copies (2-9).
3. Press
. The length of the label and the number of
copies shows on the display while the label prints.
4. When printing stops, press the
Cut button to cut
the tape. A cut mark will be printed between each
copy. Using scissors, cut along the marks to separate
each label.
•
•
•
Adjusting print density
1. When the power is off, press + .
2. Press
.
3. Use the
or
buttons to adjust the print
density, then press
.
Note:
The default value (0) is recommended.
Attaching labels
1. Peel off the backing paper.
2. Place the label on the desired surface and press it
down firmly.
Cleaning
Exterior
Use a dry, soft cloth or, for stubborn stains, a moist cloth
that has been wrung dry.
Caution:
Never use chemicals or solvents such as benzine,
thinner, or alcohol, or use a chemical duster. This could
damage your product.
Cleaning the print head
If the print becomes faint or distorted, the print head may
need cleaning.
Remove the tape cartridge and clean the print head
using a cotton swab moistened with rubbing alcohol, as
shown.
Troubleshooting
Messages
Message
Problem and solution
Insert tape
No tape cartridge is installed. Turn the
power off and install a tape cartridge.
Check tape!
An incompatible tape cartridge
has been installed. Check the tape
cartridge.
Check tape
cartridge
An incompatible tape cartridge
has been installed. Check the tape
cartridge.
Check battery The batteries may be running out, the
batteries may be installed incorrectly,
non-alkaline batteries are being used
with alkaline batteries, or old and new
batteries are being used together. Turn
the power off and replace batteries
with new ones, or use the optional AC
adapter. Make sure new batteries are
installed correctly.
Too many
lines
You have exceeded the maximum
number of lines (4). Press
to
delete the lines. (See “Breaking lines” in
“Editing text”.)
Text too long
Entered text is too long for the
specified label length. Press
and
adjust the Label length or make text
shorter.
Seq. num.
only 1
Sequence numbers have already been
set. You can only enter one sequence
number per label.
Text will be
deleted. OK?
When creating a label with a special
format, the current text will be deleted.
Press
to delete the text and show
the special format.
Fill every digit Entered values for barcodes are
incorrect. Make sure the barcode
format is supported and that the
correct number of values is entered.
Load wider
tape
Unable to print on the current tape.
Use a wider tape.
Txt is too long
Continue?
Entered text is too long for the
specified label length. Press
to confirm and continue printing.
The label length will be adjusted
automatically.
Overheated!
The print head is too hot. Turn the
power off and remove the tape
cartridge. Allow the print head to cool
for a while before trying to print again.
Cover open!
powering off
If you open the rear cover while the
power is on, this message displays
and the power turns off automatically.
Always turn the power off before
opening the rear cover.
Motor error!
An error occurred in the motor
operation. Turn the power off, then
turn it back on. If the same message
appears, turn the power off and
contact Epson.
Problems and solutions
Check the solutions below if you are having trouble using
your product.
The product does not function normally
The product may stop functioning due to static
electricity or other causes. If your product does not
function normally (i.e. the power doesn’t turn on/off or
the display is distorted), reset your product by following
the procedure below.
Warning:
Resetting your product will erase all saved labels
and formatting and return your product to default settings.
1. Press to turn the power off.
2. Press and hold
+
, and press .
3. When a message appears, press
(to cancel, press
any other button
).
The product will be reset.
Power is on but no images appear on the display
Make sure the batteries are inserted correctly.
Replace the batteries with new ones, or use the optional
AC adapter (APT0615Z1-1).
Warning:
Make sure to use AC adapter APT0615Z1-1 or
damage may occur.
If you are using an AC adapter, make sure that it is
securely connected to both the wall outlet and the
product.
Adjust the contrast (see “Display settings”).
The display turns off
The power turns off automatically if the product is idle
for more than 5 minutes.
If an incorrect button sequence is entered, the display
may flicker or turn off for an instant.
Nothing prints
Make sure that text has been entered.
Replace the tape cartridge, if necessary.
Check the display for an error message and perform the
suggested solution.
Replace the batteries with new ones, or use the optional
AC adapter (APT0615Z1-1).
Make sure the rear cover is closed.
Characters do not print properly
Make sure the tape cartridge is correctly seated.
Clean the print head.
Change the font (sometimes symbols do not print
properly when certain fonts are selected).
Printing stops in the middle of text
Install a new tape cartridge.
Replace the batteries or use the optional AC adapter
(APT0615Z1-1).
Saved labels are missing
You may have accidentally deleted the text by pressing
+
.
If the product is reset, all of the previously entered text
will be deleted.
If the AC adapter is unplugged or the batteries are
removed during operation, the text may be deleted.
Cannot attach the label
Make sure to peel off the backing paper before
attaching the label.
Make sure the surface you are attaching to is clean
and dry. The label may not adhere to some materials,
rough or uneven surfaces, or surfaces subjected to
extreme environmental conditions, such as high
humidity or heat.
Specifications
Dimensions
(approximate)
Width 4.33 inches (110 mm)
Depth 6.70 inches (170 mm)
Height 2.20 inches (56 mm)
Weight
(approximate)
14 oz (400 g) (excluding batteries, tape
cartridge)
Operating
temperature
50 to 95 ºF (10 to 35 ºC)
Storage
temperature
14 to 131 ºF (-10 to 55 ºC)
Power supply -
optional
AC adapter
Model
APT0615Z1-1
Manufacturer Seiko Epson Corp.
Input
AC100-240 V, 0.3 A,
50-60 Hz
Output
DC6.5 V, 1.5 A
Total output
power
10 W
Power supply -
batteries
AA alkaline battery x 6
Supported
tape widths
(approximate)
1/4” (6 mm), 3/8” (9 mm),
1/2” (12 mm), 3/4” (19 mm)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Epson technical support
Visit
epson.com/support
(U.S.) or
epson.ca/support
(Canada) where you can view manuals, get FAQs, or e-
mail Epson.
To speak with a support specialist, call:
U.S.:
(562) 276-7245, 6
am
to 8
pm
, Pacific Time, Monday
through Friday, and 7
am
to 4
pm
, Saturday.
Canada:
(905) 709-2567, 6
am
to 8
pm
, Pacific Time,
Monday through Friday.
Days and hours of support are subject to change without
notice. Toll or long distance charges may apply.
Recycling
Epson offers a recycling program for end of life products.
Please go to
www.epson.com/recycle
for information
on how to return your products for proper disposal.
Purchase supplies and accessories
Epson offers a wide array of tapes for multiple uses.
See the table below for a list of recommended tapes (1/2”
[12 mm] widths are listed). For a complete list of available
tapes, including additional widths, visit
epson.com/LW400Tapes
.
You can purchase tape cartridges and accessories at
www.epson.com/LabelWorks
(U.S. sales) or
www.epson.ca/LabelWorks
(Canadian sales). You can
also purchase supplies from an Epson authorized reseller.
To find the nearest one, call 800-GO-EPSON
(800-463-7766).
Type
Tape color
Text color Part
number
Standard
White
Black
LC-4WBN9
White
Red
LC-4WRN9
White
Blue
LC-4WLN9
Clear
Black
LC-4TBN9
Clear
Gold
LC-4TKN9
Espresso
White
LC-4NWT5
Black
Gold
LC-4BKP9
Black
White
LC-4BWV9
Metallic
Silver
Black
LC-4SBM9
Gold
Black
LC-4KBM9
Iron-on
fabric
White
Black
LC-4WBQ5
Blue
Black
LC-4LBQ5
Pink
Black
LC-4PBQ5
Glow-in-the-
dark
Glow-in-the-
dark
Black
LC-4ZBU1
Pearlized
Pink
Black
LC-4RBL9
Green
Black
LC-4GBL9
Blue
Black
LC-4LBL9
Pattern
White polka-
dot on pink
Gray
LC-4EAY9
Blue plaid on
white
Gray
LC-4CAY9
Epson is a registered trademark and Epson Exceed Your Vision is
a registered logomark of Seiko Epson Corporation. LC tape and
their logos are registered trademarks or trademarks of Seiko Epson
Corporation.
General Notice: Other product names used herein are for
identification purposes only and may be trademarks of their
respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2011 Epson America, Inc. 6/11
CPD-34893
Printed in China
Read these instructions before using your product.
User’s Guide
*41209250*
*412092500*
