Epson LQ-570e Скачать руководство пользователя страница 199

Страница: 199 / 248

Specifications

C-5

Electrical

Note:

Check the label on the back of the printer for the voltage of your printer.

Reliability:

Total print volume

19 million lines
(except print head)
MTBF 10,000 POH
(25% duty)

Print head life

approx. 200 million
strokes per wire

Dimensions and
weight:

Height

160 mm (6.3 inches)

Width

415 mm (16.3 inches)

Depth

368 mm (14.5 inches)

Weight

approx. 7.5 kg (16.5 lb)

Ribbon:

Black ribbon cartridge (#7753)
Film ribbon cartridge (#7768)
Black ribbon life

2 million characters
(LQ, 10 cpi, 48 dots/
character)

Film ribbon life

0.2 million characters
(LQ, 10 cpi, 48 dots/
character)

120 V Model

220 to 240 V Model

Input voltage range

99 to 132 V

198 to 264 V

Rated frequency range

50 to 60 Hz

Input frequency range

49.5 to 60.5 Hz

Rated current

1.0 A (maximum
2.6 A depending
on the character
type)

0.5 A (maximum
1.4 A depending
on the character
type)

Power consumption

Approx. 36 W (ISO/IEC 10561 letter pattern)

Содержание LQ-570e

























































































































































































































































Результаты поиска

Содержание LQ-570e

Отзывы:

Epson LQ-570e, Руководство пользователя, Страница: 199 / 248

Результаты поиска

Содержание LQ-570e

Отзывы: