Epson EpsonNet C82391 Скачать руководство пользователя | Manualshive

Страница: 51 / 299

background image

4

Settings for NetWare

4-5

Using Bindery Print Server (NetWare 3.1x/4.1x)

This section contains instructions on using the interface card in
Print Server mode under NetWare 3.1x/4.1x/IntranetWare with
Bindery emulation.

Configuring for NetWare using EpsonNet WinAssist

Configure the interface card using EpsonNet WinAssist.

Note:

The Novell Client32 or Novell IntranetWare Client must be installed in
your computer. Do not use Novell Client for Windows 95/98 version
3.00 or Novell Client for Windows NT version 4.50.

1. Turn on the printer with the interface card.

2. From any NetWare client, log in to the target NetWare server

with supervisor privileges. You must log in with bindery
connection.

3. Run EpsonNet WinAssist from the Start menu.

«
...
49
50
51
52
53
...
»

Содержание EpsonNet C82391












































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EpsonNet C82391

Бренд: Oki Страницы: 161

Бренд: Oki Страницы: 84

Бренд: Oki Страницы: 51

Бренд: Oki Страницы: 40

Бренд: Oki Страницы: 20

Бренд: TE Connectivity Страницы: 2

Бренд: TE Connectivity Страницы: 2

Бренд: Xerox Страницы: 3

Бренд: Zonet Страницы: 33

Бренд: Lexmark Страницы: 11

Бренд: Partner Страницы: 34

Бренд: Lanier Страницы: 4

x3350 - System - 4192

Бренд: IBM Страницы: 98

x3500 - System - 7977

Бренд: IBM Страницы: 124

Бренд: IBM Страницы: 106

x3200 - System M3 - 7328

Бренд: IBM Страницы: 100

System x3400 Type 7975

Бренд: IBM Страницы: 124

System x3300 M4

Бренд: IBM Страницы: 470

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды