Epson EpsonNet C82391 Скачать руководство пользователя

Страница: 28 / 299

1-6

Getting Started

Initializing the Interface Card

You must initialize the interface card in the following cases:

❏

The first time you turn on the printer after installing the
interface card

❏

When the utility does not recognize the interface card because
of settings conflicts on the network

❏

If you forget the configuration utility’s password

Follow these steps to initialize the interface card.

1. Make sure that the printer with the interface card is turned off.

2. While holding down the status sheet button, turn the printer

on.

3. Hold down the status sheet button for about twenty seconds

until the red status light and green data light turn on. These
lights indicate that the interface card is being initialized.

4. After initialization is complete, press the status sheet button

to print a status sheet. Check the information on the status
sheet.

Содержание EpsonNet C82391












































































































































































































































































































Результаты поиска

Содержание EpsonNet C82391

Отзывы:

Похожие инструкции для EpsonNet C82391

Бренды по названию

Популярные бренды

Epson EpsonNet C82391, Руководство администратора

Результаты поиска

Содержание EpsonNet C82391

Отзывы:

Похожие инструкции для EpsonNet C82391

Бренды по названию

Популярные бренды