Epson DM-D110 Series Скачать руководство пользователя страница 78

Страница: 78 / 110

Precautions when Using the USB Models

This section explains the usage precautions when using a USB connection (self powered and bus powered).

Precautions when using the serial (USB controlled)

Make sure you turn on the customer display first, and then turn on the TM printer. Otherwise the TM printer
cannot recognize the customer display.

Precautions

Controlled

environment

SON OPOS

ADK

SON

OPOS ADK f

r .NE

EPSON Ja

POS

ADK

EPSON A

ed Prin

ter

Driv

When using the DM-D110 Virtual COM Port Driver, set the communication speed for the dip

switch to 115200 bps.

✔

Before putting Windows to system standby status, Release/Close this product.

✔

In the following situations, Release this product and the Claim again.



When putting Windows to system standby status and then restarting.



When you have turned off this product and turned it again on while application is still run-

ning.

✔

While the application software is running, do not remove the USB cable for this product.

✔

Do not share this product from multiple application software.

✔

Содержание DM-D110 Series















































































































Результаты поиска

Содержание DM-D110 Series

Отзывы:

Похожие инструкции для DM-D110 Series

Бренды по названию

Популярные бренды

Epson DM-D110 Series, Техническое справочное руководство

Результаты поиска

Содержание DM-D110 Series

Отзывы:

Похожие инструкции для DM-D110 Series

Бренды по названию

Популярные бренды