Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Скачать руководство пользователя

Страница: 98 / 129

Options and Consumables

Chapter 5

Options and Consumables

The following options are available for your LX-300+II:

❏

Single-bin cut-sheet feeder (C806371)

❏

Additional tractor (C800301)

❏

Roll paper holder (#8310)

❏

Black ribbon cartridge (#8750)

Cut-sheet Feeder

The optional single-bin cut-sheet feeder (C806371) handles up to
50 sheets of standard bond paper (22 lb or 82 g/m²) without
reloading.

Follow these steps to install the cut-sheet feeder:

1. Make sure the printer is turned off. Remove the paper guide

and open the printer cover.

2. If the tractor is installed in the pull-tractor position, remove

it and reinstall it in the push-tractor position.

3. Make sure the paper release lever is in the single-sheet

position.

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer


































































































































Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды

Epson C11C640001 - LX 300+II B/W Dot-matrix Printer, Справочное руководство

Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды