Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Скачать руководство пользователя

Страница: 119 / 129

Product Information

119

Printable area

Single sheets and envelopes:

The minimum top margin is 0.17 inch (4.2 mm).

The minimum left and right margins are 0.12 inch (3.0 mm).

For single sheets the maximum paper width is 10.1 inches
(257 mm).

The maximum printable width is 8.0 inches (203.2 mm).
If the paper size is substantially wider than this, the side
margins will be wider than the minimum, but the printable
width does not increase beyond 8.0 inches (203.2 mm).

The minimum bottom margin is 0.17 inch (4.2 mm).

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer


































































































































Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды

Epson C11C640001 - LX 300+II B/W Dot-matrix Printer, Справочное руководство

Результаты поиска

Содержание C11C640001 - LX 300+II B/W Dot-matrix Printer

Отзывы:

Похожие инструкции для C11C640001 - LX 300+II B/W Dot-matrix Printer

Бренды по названию

Популярные бренды