Epson AcuLaser M4000 Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 217

Epson AcuLaser M4000 Series Скачать руководство пользователя страница 24

AcuLaser M4000 Series

User's Guide

Getting to Know Your Printer

24

Options and Consumable Products

Options

You can add to your printer’s capabilities by installing any of the following options.

❏

550-Sheet Paper Cassette Unit (C12C802471)
This unit increases paper feeding capacity up to 550 sheets of paper. You can install up to two
units.

❏

Duplex Unit (C12C802481)
This unit allows for automatic printing on both sides of paper.

❏

Stacker (C12C802111)
This unit provides the offset function. The printouts are output in offset stacks. The Stacker can
stack up to 500 sheets of paper.

❏

Hard Disk Drive (C12C824172)
This option expands the printer’s capacity by allowing you to print complex and large print
jobs at high speed. This option also enables you to use the Reserve Job function. By using the
Reserve Job function, you can store print jobs in the printer’s hard disk and print them later
directly from the printer’s control panel.

❏

Memory Module
This option expands the printer’s memory by allowing you to print complex and
graphics-intensive documents. The printer’s RAM can be increased up to 576 MB by adding
two additional 256 MB RAM DIMMs.

Note:

Make sure that the DIMM you purchase is compatible with EPSON products. For details, contact the
store where you purchased this printer or an EPSON qualified service representative.

Consumable products

The life of the following consumable products is monitored by the printer. The printer lets you
know when replacements are needed.

Product name

Product code

Imaging Cartridge

1170

Fuser Unit (110-120 V)

3037

Fuser Unit (220-240 V)

3038

«
...
22
23
24
25
26
...
»

Содержание AcuLaser M4000 Series


























































































































































































































Отзывы:

Нет отзывов