Epson AcuLaser M4000 Series Скачать руководство пользователя страница 199

Страница: 199 / 217

AcuLaser M4000 Series

User's Guide

Technical Specifications

199

Printer

General

Printing method:

Laser beam scanning and dry electrophotographic process

Resolution:

300

300 dpi, 600

600 dpi, 1200

1200 dpi

Continuous printing speed

A maximum of 43 pages per minute on A4 size paper

Paper feed:

Automatic or manual feed

Paper feed alignment:

Center alignment for all sizes

Input paper supply:

MP tray:

plain paper

Up to a 17.5 mm thick stack, or up to 150
sheets (80 g/m²)

envelopes

Up to a 17.5 mm thick stack

transparencies

Up to a 11.9 mm thick stack, or up to 100
sheets

labels

Up to a 17.5 mm thick stack

thick paper

Up to a 17.5 mm thick stack

extra thick paper

Up to a 17.5 mm thick stack

Standard lower paper cassette:

plain paper

Up to a 59.4 mm thick stack, or up to 550
sheets (80 g/m²)

envelopes

Up to a 49.4 mm thick stack

transparencies

Up to a 12.4 mm thick stack, or up to 100
sheets

labels

Up to a 49.4 mm thick stack

thick paper

Up to a 49.4 mm thick stack

extra thick paper

Up to a 49.4 mm thick stack

Paper output:

Face-down tray

For all paper types and sizes

Face-up tray

For all paper types and sizes

Stacker

For all paper types
For 89.9 to 215.9 mm width paper
See “Stacker” on page 205 for details.

Paper output capacity:

Face-down tray

Up to 500 sheets of plain paper (80 g/m²)

Face-up tray

Up to 70 sheets of plain paper (80 g/m²)

Stacker

Up to 500 sheets of plain paper (80 g/m²)

Содержание AcuLaser M4000 Series


























































































































































































































Результаты поиска

Содержание AcuLaser M4000 Series

Отзывы:

Epson AcuLaser M4000 Series, Руководство пользователя, Страница: 199 / 217

Результаты поиска

Содержание AcuLaser M4000 Series

Отзывы: