manualshive.com logo in svg

Epson ActionPrinter 4500, Руководство пользователя, Страница: 270 / 317

Поделиться
Скачать
Epson ActionPrinter 4500 Скачать руководство пользователя страница 270

Commands Arranged by Topic

Horizontal Motion

ESC 1

Format:

ASCII code:
Decimal:

Hexadecimal:

Comments:

ESC 1 n

27

108 n

1B 6C n

Set Left Margin

Sets the left margin to n columns in the current character size.

Settings made in the proportional mode are treated as 10 cpi. This
command clears previous tab settings and all previous characters in
the print line. Use lowercase 1 (as in left), not the numeral one. The
minimum space between the margins is the width of one double-wide
10 cpi character.

ESC Q

Format:

ASCII code:
Decimal:

Hexadecimal:

ESC Q 

n

27 81 n
1B 51 n

Set Right Margin

Comments:

Sets the right margin to n columns in the current character size.
Settings made in the proportional mode are treated as 10 cpi. This
command clears previous tab settings and all previous characters in

the print line. The minimum space between the margins is the width
of one double-wide 10 cpi character.

Command Summary

9-19

Содержание ActionPrinter 4500






























































































































































































































































































































Отзывы:

Нет отзывов