Epson ActionPC 5000 Скачать руководство пользователя страница 80

Страница: 80 / 176

While holding down the

ALT

button, press

the

LOAD/EJECT

button to feed the paper forward or the

LF/FF

button to

feed the paper backward, as indicated by the arrows above
the buttons.

Adjusting the loading position

The loading position is the position of the paper after it has
been automatically loaded by the printer. If printing is too high
or low on the page, change the loading position with the
micro-feed feature as follows:

Make sure the printer is turned on. If necessary, lift the

printer cover up so you can see the paper position.

2. Load either continuous or single-sheet paper. (Load

continuous paper by pressing the

LOAD/EJECT

button.)

The

MULTI-PART

light

begins to flash.

Note:

You can adjust the loading position only while the

MULTI- PART

light

is flashing.

Using the Printer

3-15

Содержание ActionPC 5000

















































































































































































Результаты поиска

Содержание ActionPC 5000

Отзывы:

Epson ActionPC 5000, Руководство пользователя, Страница: 80 / 176

Результаты поиска

Содержание ActionPC 5000

Отзывы: