EPS PSB 10000 4U Скачать руководство пользователя страница 76

Страница: 76 / 110

30000800_manual_psb_10000_4u_30kw_en_04

3.11.4

Manual operation

3.11.4.1 Function selection and control

All the functions listed in

3.11.1 can be called on the touch screen,

configured and controlled. Selection and configuration are only

possible while the DC terminal is switched off.

►

How to select a function and adjust parameters

While the DC terminal is switched off tap touch area

on the main screen. Note: this icon is locked as

long as resistance mode (R mode) is enabled.

In the menu select the desired function by tapping on the list on the left-hand side. Depending on the choice of function

there follows a request to which value the function generator is going to be applied,

Voltage

Current

Adjust the parameters as you desire.

Adjust the overall limits of voltage, current and power, then continue with

As last part of the configuration, global set values have to be defined which are considered as static values and come

into effect before and after the function run. Correct setup here is important, especially when running the function on

a master device of a master-slave system.

•

When intending to run a function exclusively in sink or in source mode, it’s recommended to set

the set values (I, P) of the opposite mode to 0.

•

The global limits of U, I and P become instantly active when coming to the main screen of the

function generator, because the DC terminal is then switched on automatically to settle the start

situation. This can be helpful when wanting a function shall not start at 0 V or 0 A. In case the

situation requires otherwise, the static values could also be set to 0.

Exit the configuration and enter the main function generator screen with

Setting the various functions and their parameters is described below. After the function generator screen has been reached,

the function is ready to run. Before and while the function is running, some global and also some function related values can

be adjusted anytime.

►

How to start and stop a function

The function can be

started

either by tapping

or if the

DC terminal is currently switched off by pushing the “

On/Off

”

button on the front.

The function can either be

stopped

by tapping

or op-

erating the “On/Off” button. However, there is a difference:

a) The

button only stops the function while the DC

terminal remains ON with the static values in effect.

b) The “On/Off“ button stops the function and switches the

DC terminal off.

Any device alarm (power fail, overtemperature etc.), protection (OPP, OCP) or event with Action = Alarm

stops the function progress automatically, switches off the DC terminal and reports the alarm.

Содержание PSB 10000 4U















































































































Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды

EPS PSB 10000 4U, Руководство по эксплуатации

Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды