Epple Maschinen PW 30 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 50

background image

Stand 31.07.08, PW 30, PW 30 HV, Profile roll

Page 17 of 50

3 Assembly

The machine is delivered pre

– mounted.

3.1

Delivery volume

After receipt of the delivery you have to check directly of shortfalls. Compare
the scope of delivery with the information at the packing slip.
Check whether the machine has damages in transit.

.

3.2

Transport

Warning!

If the lifting tool is not stable enough it can burst what may cause heavy or deadly
injuries. Please observe the following instructions for the carrier box/ palette:



Rope stops



Weight



Balance point



Prescribed means of transport

Warning!

If the lifting tool is not stable enough it can burst what may cause heavy or deadly
injuries. Check before working with lifting tool whether it is admitted for the load
and undamaged. Observe the effective accident prevention regulations for your
business. Never step under lifted loads for your own safety. See that the load is
fixed correctly.

3.3

Storage

By an improper storage the machine or machine parts can be damaged.
Never store the machine under other environmental conditions than in the
operation manual denoted. The warranty claim declines by improper storage.

«
...
15
16
17
18
19
...
»

Содержание PW 30



















































Отзывы:

Нет отзывов

Похожие инструкции для PW 30

Бренд: ABB Страницы: 18

Бренд: R-Tech Страницы: 3

D-IMager EKL3104

Бренд: Panasonic Страницы: 13

Бренд: Labokey Страницы: 5

Бренд: E-Z Trail Страницы: 8

Бренд: B&K Страницы: 10

Бренд: TC Electronic Страницы: 2

Бренд: Bahco Страницы: 131

Бренд: Bahco Страницы: 126

Бренд: JBL Страницы: 38

Бренд: JBSYSTEMS Light Страницы: 32

Бренд: JBM Страницы: 12

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды