background image

 

 
 

Stand 31.07.08, PW 30, PW 30 HV,  Profile roll                               

Page 15 of 50 

 

1.10.1  Breaking and assuring the machine 

 

Deactivate  the  machine  before  the  beginning  of  attendance  and  maintenance 
work with the main switch. Assure the main switch with a u 

– lock and retain the 

key. If applicable brew the mains plug. 

                  Mark and assure the machine clearly against unauthorised resetting.  

 

Warning! 

Moves  of  machine  parts  and  electric  machine  parts  can  hurt  you  and 
others  heavy.  Act  very  careful  if  it  is  not  necessary  to  unplug  the 
machine  because  of  working.  Inform  personnel  around  you  about  your 
cycle and the possible dangers. 

 

1.10.2  Use of hoisting devices for attendance work 

 

Warning! 

If the lifting tool is not stable enough it can burst what may cause heavy 
or deadly injuries. 
Check before working with lifting tool whether it is  admitted for the load 
and  undamaged.  Assure  that  the  load  is  fixed  correctly.  Never  step 
under  lifted  loads.  Please  observe  the  effective  accident  prevention 
regulations for your business. 

 

1.10.3  Mechanic attendance work at the machine 

 
Before or after attendance work: 
 
Replace all protection and safety units that are especially for attendance 
work  and  activate  the  machine  with  the  machine 

–  own  protection  and 

safety  units.  Check  the  protection  and  safety  units  after  every 
attendance  or  maintenance  work  about  completeness  and  correct 
function. 
 

1.11  Accident report 

 
Inform your superior directly about acciden

ts or “nearly accidents”.  

So 

–  called  „nearly  accidents“  can  have  different  causes  and  need  a  detailed 

analysis. 
 
 
 

1.12  Electricity 

 
You are bound to let the electrical equipment of the machine check regularly. 
We  advise  you  at  least  a  checking  every  6  months.  Deficiencies  like  damaged 
cables  or  not  fixed  connections  you  have  to  correct  always  immediately 
underneath  observance  of  the  safety  measures.  During  work  at  live  parts  a 
second person always has to be attendant who can switch 

– off the machine in 

an emergency.  
The machine must be out off gear immediately by failure in the electrical supply. 
 



 You will find more information in chapter maintenance 

Содержание PW 30



















































Отзывы: