Epilog Laser Fusion Скачать руководство пользователя

Страница: 1 / 10

Adjusting the Table Level
Fusion and FiberMark Fusion
Revision Date: 9/10/2014

pg. 1 of 10

EPILOG LASER

16371 Table Mountain Parkway
Golden, Colorado 80403
Phone 303-215-9171
FAX 303-277-9669
www.epiloglaser.com

Adjusting the Table Level

For the Epilog Fusion and FiberMark Fusion

9/ 10/ 20 14

Requirements:

Tools:

•

3/32” Allen Wrench

•

Manual Focus Gauge

When to use this document:

•

Uneven power in various areas of the table.

•

Reduction in quality in various areas of the table.

•

General reduction in power or quality.

•

Inconsistent or Inaccurate Auto Focus.

•

When instructed by Epilog Tech Support.

Overview:

This procedure will guide you through the process of properly checking and

adjusting the table level on the Epilog Fusion. This will ensure proper focus on every
point of the engraving area.

Содержание Fusion











Результаты поиска

Содержание Fusion

Отзывы:

Похожие инструкции для Fusion

Бренды по названию

Популярные бренды

Epilog Laser Fusion, Руководство пользователя

Результаты поиска

Содержание Fusion

Отзывы:

Похожие инструкции для Fusion

Бренды по названию

Популярные бренды