EOS P 396 Скачать руководство пользователя страница 81

Страница: 81 / 170

Part Property Management

5.11

Training manual • Basic training • Status 03.14

EOS P 396

➢

Exposure type

No_Exposure

If a part is allocated this exposure type, it is not exposed during the building

process.

Exposure editor

Using the

Exposure editor

module, new, custom exposure types with custom

parameters can be prepared. The basic exposure types in the Exposure editor do not

contain any initial values that can be used for building. These values must be

prepared independently or obtained using the

Initial values for parameters

module.

Possible applications:

➢

Process optimisation for special applications

➢

Development of optimised exposure parameters for parts with very complex

geometries

➢

Research and development in the area of laser sintering.

Exposure parameters window

You will find an overview of the exposure types in the

Exposure editor

module in

the

Operation

manual, section 5,

Exposure types in the Exposure editor module

Содержание P 396











































































































































































Результаты поиска

Содержание P 396

Отзывы:

Бренды по названию

Популярные бренды

EOS P 396, Руководство по обучению

Результаты поиска

Содержание P 396

Отзывы:

Бренды по названию

Популярные бренды