Enviro Evolution Скачать руководство пользователя страница 25

Страница: 25 / 36

Installation

HERMOSTAT

NSTALLATION

If the unit has been placed in the HI / LOW mode, the unit will be taken to a low or idle setting when the

thermostat is not calling for heat. When the thermostat calls for heat, the unit will go to the setting that

is displayed on the control board Heat Indicator. If the heating load is not great enough when the stove

is on low, the high limit switch will turn the stove off and the switch will have to be manually reset. To

reset the high limit switch, remove the right cabinet side. The switch is found behind the control panel.

Avoid setting off the high limit switch.

PTIONAL

LIDER

AMPER

NSTALLATION

A) HI / LOW:

When the jumper is placed

on only one of the J9 pins,

then the control board is in a

HI / LOW mode of thermostat

operation (factory setting).

B) ON / OFF:

If both pins of J9 are jumped

(covered), the control board

is in an ON / OFF mode of

thermostat operation.

Remove jumper wire and install

thermostat wires here

Figure 26: Circuit Board.

This control board can be placed into two

different modes: When the jumper J9 is

not jumped then the control board is in a

HI / LOW mode operation. If the control

board is placed with J9 jumped then the

control board is in a ON / OFF mode of

operation. In the ON /OFF thermostat

mode, the unit will shut OFF when the

thermostat is not calling for heat. When

the thermostat calls for heat, the unit will

go through an ignition sequence once

again and relight.

1. Install the wall thermostat in a location

that is not to close too the unit but will

effectively heat the desired area.

2. Install a 12 or 24 Volt Thermostat using

an 18 x 2 gauge wire from the unit to

the thermostat.

Slider damper

rod and knob

" Nut

" Clinching Nut

Slider damper plate

1. To install the OPTIONAL slider damper rod, remove the left cabinet

side and locate the slider damper plate. Install the

” inch nut

onto the slider damper rod, thread all the way to the end of the

threads on rod.

2. Slide rod through the hole in the slider damper plate and install the

” clinching nut onto the rod and tighten completely onto the slider

damper plate.

3. Re-install the cabinet side. Install the black knob on the end of the

rod. Check slider damper for smooth operation.

Slider/

Damper

Knob

NOTE: NOT FOR USE IN GERMANY

If you wish to adjust the slider damper externally (NOT

REQUIRED), please follow the instructions below.

Figure 27: Slider/Damper Assembly.

Figure 28: Slider/Damper Knob.

Содержание Evolution





































Результаты поиска

Содержание Evolution

Отзывы:

Похожие инструкции для Evolution

Бренды по названию

Популярные бренды

Enviro Evolution, Руководство пользователя

Результаты поиска

Содержание Evolution

Отзывы:

Похожие инструкции для Evolution

Бренды по названию

Популярные бренды