background image

4

November 2011

Location of the Pellet Fire

Installation  of  the  Enviro  Classic  Wood  Pellet  Burning  Heater  should  be  undertaken  by  an 

experienced  installer.  Please  read  the  Classic  Owners/Technical  Manual  thoroughly  before 

commencing installation as failure to follow the instruction could cause damage to the pellet 

fire or property. 

Positioning the fire:

Generally the Classic should be installed in a centrally located position within the home. When 

deciding where to position the appliance in your room you need to consider the following:

• 

Location of a power source

• 

The Classic has a convection fan which blows air through tubes in the direction that the 

fire faces, for optimum performance this location should be in a large room centrally 

located.

• 

The Classic must be installed on a non-combustible surface. This surface must protrude 

150mm from the front of the closed pellet fire door.

• 

The Classic has been Safety Tested to AS/NZS 2918 using the Davins manufactured 

flue. Test  Report ARS  05/1185.  Installation  is  not  exclusive  to  these  nominated  kits, 

though alternative flue should only be considered following consultation with your local 

council.

• 

Please consult page 3 for the required clearances to combustible material also ensure 

the position of structural elements near the proposed flue.

• 

Because  of  the  positive  pressure  in  the  flue,  sealing  of  all  75mm  stainless  joints  is 

mandatory – use high temperature sealant.  Both inner and outer flue joints must be 

riveted.

• 

Seismic Restraint:  Please see page 9 for requirements.

• 

Warranty:  To validate warranty following installation a copy of the completed Warranty 

Registration Form/Producer’s Statement must be forwarded to: Switch - Fax (03) 341 

8057.

Содержание EF2










Отзывы: