Entre Matic Ditec DAB105 страница 48 Скачать руководство пользователя | Manualshive

Страница: 48 / 50

background image

48

IP2159EN - 2017-06-12

23. Troubleshooting

Problem

Possible cause

Solution / Explanation

The door does not open

a) The motor does not start

The function selector is set on OFF

Change the function selector setting

There is no mains power supply

Check the mains power supply

The command unit does not work

Check the connections of the command ac-
cessories

The motion sensor has been activated

Remove any objects from the detection area

Emergency closure activated

Deactivate the emergency closure

SPTE trimmer not set to 0°

Rotate the SPTE trimmer to 0°

b) The motor starts

Mechanical lock blocked

Release the lock

Obstacle

Remove any obstacles

Door stop jammed

Select block release

The arm system is coming loose

Rotate the SPTE trimmer until the door stop is
on the limit switch.
Bring the door to its open position.
Tighten the arm system.
Rotate the SPTE trimmer to 0°

The door does not close

The selector is set on DOOR OPEN

Change the function selector setting

The motion sensor contact has been activated

Remove any objects from the detection area

Obstacle

Remove any obstacles

The spring pre-tensioning on the automatic
system is unrecognised

Too many adjustments have been made

1. Rotate the SPTE trimmer until the end

stop can be loosened.

2.  Remove the end stop and the arm system.
3.  Disconnect the mains power supply.
4.  Disconnect the motor cable
5.  Replace the arm system and locate the

non-pretensioning point by moving the
door wing backwards and forwards.

6.  Loosen the arm.
7.  Reconnect the motor cable.
8.  Reconnect the mains power supply.
9.  Adjust the SPTE trimmer at 210° and wait

for the shaft to stop rotating.

210°

10. Fix the end stop on the closure limit

switch.

11. Set the SPTE trimmer to 0°.
THE AUTOMATIC SYSTEM HAS RETURNED TO
THE FACTORY SETTINGS.
12. Repeat the door start-up operations

explained in chapter 12

«
...
46
47
48
49
50
»

Содержание Ditec DAB105



















































Отзывы:

Нет отзывов

Похожие инструкции для Ditec DAB105

Бренд: Kaba Страницы: 4

Бренд: CHIEF Страницы: 8

Emtek multipoint handle set

Бренд: Westeck Страницы: 2

Pivot Shower Doors 950C Series

Бренд: Sterling Plumbing Страницы: 12

Бренд: ilco Страницы: 2

Бренд: I.H.T Страницы: 2

Бренд: IEI Technology Страницы: 2

Бренд: Kaadas Страницы: 29

Бренд: Falcon Страницы: 10

Бренд: Falcon Страницы: 29

Бренд: Falcon Страницы: 56

Бренд: Falcon Страницы: 63

Бренд: Assa Abloy Страницы: 6

Бренд: JAKO Страницы: 2

Бренд: Videosec Страницы: 11

Бренд: Conrad Electronic Страницы: 118

Бренд: Adel Страницы: 10

Бренд: Adel Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды