background image

 

IQ 7 / IQ 7+ / IQ 7X / IQ 7A with EN4 Bulkhead Installation and Operation 

 

© 2020 Enphase Energy Inc. All rights reserved. 

141-00047-01 

 

41 

Q Cable Specifications 

Specification 

Value 

Voltage rating 

600V 

Voltage withstand test (kV/1min) 

AC 3.0 

Max DC conductor resistance (20º

C) (Ω/km) 

5.433 

Insulation resistance (20ºC) 

≥20M (Ω/km) 

System temperature range (ambient) 

-40ºC to +65ºC (-40ºF to 149ºF) 

Cable temperature rating 

90ºC Dry / 90ºC Wet 

Cable rating 

DG 

Certification 

UL 3003, TC-ER equivalent  

Flame test rating 

FT4 

Cable conductor insulator rating 

THHN/THWN-2 

Environmental protection rating 

IEC 60529 IP67 NEMA 6 

UV resistance 

720h 

Compliance 

RoHS, OIL RES I, CE, UV Resistant, combined UL for Canada 
and United States 

Conductor size 

12 AWG 

Maximum loop size 

12 cm (4.75 

“) 

Flat cable dimensions 

6 mm x 9.5 mm (0.2” x 0.37”) 

Sealing cap dimensions 

38.6 mm x 20 mm 

(1.5” x 0.7”) 

Cable connector dimensions 

20 mm x 1.1 mm x 6.5 mm 

(0.7” x 0.04” x 0.25”) 

 

 

Enphase Connector Ratings 

Enphase Connectors on the cable assemblies in the following table have a maximum current of 20 A, a 
maximum OCPD of 20 A, and maximum ambient temperature of -40° to +79° C (-40° to +174.2° F) and 
are rated for disconnection under load. 
 

Part Number 

Model 

Maximum Voltage 

840-00387 

Q-12-10-240 

250 VAC 

840-00388 

Q-12-17-240 

250 VAC 

840-00389 

Q-12-20-200 

250 VAC 

860-00311 

ECA-EN4-S22 

80 VDC 

860-00315 

ECA-EN4-S22-L 

80 VDC 

860-00312 

ECA-EN4-FW 

80 VDC 

 

Содержание IQ 7












































Отзывы: