ENMET MedAir 2200 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 41

ENMET MedAir 2200 Скачать руководство пользователя страница 7

MedAir

ENMET

Manual Release Date – June 9, 2017

P a g e

| 6

Manual Part No. – 80002-042

2.3 Circuit Board Features

The Display Panel is hinged on the left and is released by unscrewing the 2 screws located in the right corners. After releasing the
panel, it is swung to the left, exposing the interior of the enclosure. The Circuit Board is mounted at the back surface of the
enclosure interior. Features are shown in

Figure 2

.

Feature

Description

Relay Terminals

This group of terminals is located at the left side of the Circuit Board.
For the contacts for each of four alarm relays, and for the contacts of a fault relay.

Output Terminals

One 4-20mA output per active channel. 2 channels/outputs per connector.

Sensor Manifold

The sample manifold, the carbon monoxide, carbon dioxide and oxygen sensors are
located under this housing.

Dew Point Manifold

The dew point sensor is installed into this housing.

Figure 2: M

ED

A

IR

2200

Interior Features

Power Input

Terminal J23

Audio
Alarm

Sensor Dew Point

If Dew Point option is

installed

Relay Terminals

(6 places)

Aux Terminals

Optional (2 places)

Dew Point Terminal

Optional

Horn Terminal

Fuse Holders

0.630 Amp

(2 places)

Flow Sensor

Sensor
Manifold

Digital
Communication

Ground Screw

J21

Dew Point Manifold

If Dew Point option is

installed

4 – 20mA Output

Terminals

4 places

«
...
5
6
7
8
9
...
»

Содержание MedAir 2200










































Отзывы:

Нет отзывов