background image

 

 

A

 

base

IOM67 

11  

February 2021 R0 

 

ALARMS 

LED 

Name 

Description 

General Alarms 

01 

Low  limit 

The low limit setpoint is 
the lower of 40°F or 15°F 
below the discharge air 
setpoint.  4 minute bypass 
time. 

02 

Air Proving 
Fault 

VFD Feedback is greater 
than the minimum VFD 
speed for more than 30s 
with the supply fan output 
off. 

03 

Shorted Air 
Proving 

Air SA Proving switch 
shorted on start up. 

04 

Low airflow 

Air Proving switch opens 
during operation for 30s 
or the VFD feedback drops 
below the minimum speed 
for 30 seconds. 

05 

Discharge Air 
Sensor Failure 

Discharge Air sensor is 
outside of its range for 
10s. 

06 

Ambient Air 
Sensor Failure 

Outdoor Ambient sensor 
is outside of range for 10s. 

07 

Damper End 
Switch Short 

The damper end switch is 
made before energizing 
the damper output. 

08 

Damper End 
Switch Open 

Indication damper end 
switch not made after 
actuator is energized. 

09 

Communication 

Loss of communication to 
CD-XM (if used). 

Heating Alarms 

80 

Gas Valve 
Wiring 

Gas valve feedback has 
power before the FR and 
SR contact are energized. 

81 

Gas Valve out of 
range 

Gas valve actuator 
feedback is greater or less 
than the demand.  

Timed event. 

86 

High Limit 

High limit safety tripped 
due to excessively high 
temperature. 

87 

Flame Relay 
Wiring 

Received a gas valve 
feedback within 500ms of 
activating the Flame relay 
output. 

88 

Flame Failure 

Gas valve feedback has no 
power after 1 minute of 
enabling the Flame relay 
output. 
 

DJ/SH(X) Alarms 

82 

RPM out of 
range 

Combustion blower motor 
RPM is greater or less 
then the demand.  
Timed event. 

83 

Open Air 
Proving 

Combustion blower does 
not exceed 3000 rpm 
during purge.   

84 

Combustion Air 
Proving 

Combustion rpm speed 
sensor has a value greater 
than 500 rpm for 60 
seconds before the 
combustion blower has 
been commanded on. 

85 

Plugged 
Condensate 

Blocked condensate 

sensor reads less then 7kΩ 

for more than 5 minutes. 

89 

Blocked Flue 

Blocked flue input is open 
for more than 1 minute. 

90 

60 Hz 

Combustion blower 
frequency has exceeded 
60 Hz ( 3590 RPM) 

DG Alarms 

82 

Air Actuator 
Out of range 

Air Actuator Feedback Is 
greater or less then the 
demand. Tolerances and 
timing vary depending on 
mode of operation. 

Содержание base













Отзывы: