EnGenius EDS5255 Скачать руководство пользователя страница 165

Страница: 165 / 166

164

Appendix

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

Содержание EDS5255







































































































































































Результаты поиска

Содержание EDS5255

Отзывы:

Похожие инструкции для EDS5255

Бренды по названию

Популярные бренды

EnGenius EDS5255, Руководство пользователя

Результаты поиска

Содержание EDS5255

Отзывы:

Похожие инструкции для EDS5255

Бренды по названию

Популярные бренды