ENFORCER Request-to-Exit Button with Delayed Egress Timer
4
SECO-LARM U.S.A., Inc.
NOTICE:
The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
or in part, without the written permission of SECO-LARM.
WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in
normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to
SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or
abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-
LARM determines that such equipment is not operating properly as a result of causes other than defects in material and
workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to the
replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral,
incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA, 92606 Website: www.seco-larm.com
PITSW1
Tel: (949) 261-2999 | (800) 662-0800
Email: [email protected]
MiSD-7428-GSEQ_1404.docx
Order part # 763-178-1%
Remote Alarm Relay Output:
•
The SD-7428-GSEQ is equipped with a 3A@30VDC Form C dry relay output for a remote alarm.
•
The remote alarm relay is normally energized.
•
A remote device or alarm connected to this output will be triggered at the start of the
pre-delay timer.
•
The remote alarm output will continue signaling until the keyswitch is turned on momentarily.
•
In the event of power loss, the remote alarm relay will de-energize to trigger the remote alarm.
Troubleshooting:
Request-to-Exit Button will not
release the lock
•
Check the nuisance delay (see page 3)
•
Check the pre-delay timer (see page 3)
Door will not relock
•
Turn keyswitch to re-energize lock relay
IMPORTANT:
Users and installers of this product are responsible for ensuring that the installation and configuration of
this product complies with all national, state, and local laws and codes related to locking and egress devices.
SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
Lock Relay Output:
•
The SD-7428-GSEQ is equipped with a 3A@30VDC Form C dry relay output that can be used
with a fail-safe lock.
•
The lock relay is normally energized.
•
The lock relay will de-energize after the pre-delay time expires. The lock relay will re-energize
once the keyswitch is turned on momentarily.
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
SD-7428-GSEQ
Request-to-Exit Button
with Delayed Egress Timer
User Manual
•
Programmable nuisance delay timer
(0~3 seconds) to prevent accidental door
unlocking
•
Adjustable pre-delay timer (1~30 seconds
until the door unlocks)
•
12~24 VDC Operation
•
Form C relay outputs for lock relay and
remote alarm relay
•
Built-in 100dB buzzer
•
Fits standard double-gang backbox
•
Keyswitch to re-energize door lock
IMPORTANT
Users and installers of this product are responsible for ensuring that the installation and configuration of this
product complies with all national, state, and local laws and codes related to locking and egress devices.
SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
Replacement Keys:
SD-7428-KEY (Sold in packs of 5)
