EVP-1SA4P9UL Shown
Installation Manual
What it is:
The ENFORCER CCTV Power Supply centralizes the power sources for four,
nine, or sixteen AC-powered CCTV cameras and/or CCTV accessories. The
power input, power transformer, and all fused power outputs are enclosed in
one heavy-duty, easy-to-install enclosure. As a result, an ENFORCER CCTV
Power Supply can replace up to sixteen individual power sources.
Note before installation:
The ENFORCER CCTV Power Supply is not waterproof or weatherproof.
Therefore, it must be mounted indoors where it cannot be exposed to rain or
other moisture.
Installation must be done by qualified personnel, and should conform
to local and all other applicable codes.
L’installation doit être effectuée par un personnel qualifié et doit être
conforme aux codes locaux et tout autre code applicable.
Installation:
1.
Find a good location for the enclosure - The enclosure should be
mounted where it is out of sight and protected from moisture and the
weather, but where an authorized person can have access for servicing
in the future.
NOTE:
Make sure the space where the enclosure is to be mounted has
adequate ventilation. Otherwise, heat buildup inside the enclosure could
damage the electronic parts or cause the PTC fuses to trip needlessly.
REMARQUE:
Assurez-vous que l’espace où l’enceinte doit être installée
a une ventilation adéquate. Sinon, l’accumulation de chaleur à l’intérieur
de l’enceinte pourrait endommager les composants électroniques ou
provoquer le fusible PTC à déclencher inutilement.
2.
Locate the enclosure mounting holes. Using these holes as a template,
mark the location of the 4 screws on the wall with a pencil. First fasten
two
5
/
32
"
x 1" (4 x 26mm) upper screws (not included) until the gap
between the wall and the screw head is approximately 1/4" (6mm).
Hang the enclosure on the 2 screws using the enclosure's upper screw
holes and adjust the proper location of the enclosure. Then securely
fasten the upper and lower screws.
NOTE:
For concrete walls, first drill four holes on the concrete wall in the
location of the screws. Then insert a "plastic anchor" in each of the holes
first before fastening the screws.
Knock-Out
for Optional
Cam Lock
Ventilation
Holes
AC Power Supplies for CCTV Cameras and Accessories
FIG. 1
Cable & Power
Knock-Outs
AUDIO/VIDEO APPARATUS
26BZ
m
Enclosure:
•
Heavy-duty steel case to protect the power connections
•
Removable steel cover for easy access
•
Ventilation holes to prevent heat build-up
•
Dimensions - 10” x 7.75” x 3.5” (254 x 196 x 89 mm)
•
Knock-out on the cover for optional cam lock
Specifications:
m
4,9, or 16, 24VAC outputs:
•
Each output individually fused
•
Output fuses rated 1.1A for PTC and 1A for blade fuse
•
Individual red LED status indicator for each output
•
Main power switch to turn ON/OFF power to outputs
m
Power:
•
Input: 120VAC, 60Hz
•
Output: 24VAC/100VA (2 x 100VA for 8A versions)
•
Main fuse rated 5A@250VAC per board.
•
On board spare fuse and 6-foot power cord included
*
Positive Temperature Coefficient
EV
P
-1S
A4P4UL
EV
P
-1S
A4B4ULQ
EV
P
-1S
A4P9UL
EV
P
-1S
A4B9ULQ
EV
P
-1S
A8P1
6UL
EV
P
-1S
A8BHULQ
Model no.
4
9
16
Type of
output fuse
PTC*
Blade
PTC*
Blade
PTC*
Blade
No. of
outputs
Output
voltage
4A
4A
8A
24VAC
Total
supply
current
Max
current
per
output
1.1A
1A
1.1A
1A
1.1A
1A
ENF
OR
CE
R
®
