background image

SECO-LARM

®

 U.S.A., INC.

INSTALLATION MANUAL

ENFORCER

®

Page 8

Curtain/Barrier Sensors Installation Manual

®

PICTN1

Curtain/Barrier Sensors

(E-9622-4B25 shown)

E-9622-4B25 

-- 4-Beams

E-9644-6B25 

-- 6-Beams

E-9660-8B25 

-- 8-Beams

E-9680-10B25 

-- 10-Beams

Range: 50 ft. indoor, 25 ft. outdoor

Dimensions:

Side View

1

5

/

16

” (

33.5mm)

1

7

/

32

” (30.6mm)

7

/

8

” (

22.3mm)

3

/

4

” (19.6mm)

22.5” (57cm) -- E-9622-4B25
44.5” (113cm) -- E-9644-6B25
60.1” (153cm) -- E-9660-8B25
79” (201cm) -- E-9680-10B25

Typical

Door/Window Frame

Windows

Garages / Gates / Walls

Fence Tops

(Indoor)

Skylights

E-9622-4B25

E-9644-6B25

E-9660-8B25

E-9680-10B25

89mA

94mA

102mA

110mA

73mA

79mA

92mA

100mA

22

1

/

2

” x 1

5

/

16

” x 

7

/

8

” 44

1

/

2

” x 1

5

/

16

” x 

7

/

8

60

1

/

8

” x 1

5

/

16

” x 

7

/

8

” 79” x 1

5

/

16

” x 

7

/

8

0.5~32.5mS

0.5~48.5mS

0.5~60mS

0.5~70mS

Indoor: 50’ (16m), outdoor: 25’ (8m)
Simultaneous break of 2 adjacent beams or any single beam (programmable)
NO./NC. relay output, 1A @ 12 ~ 24VDC
-49°~131° F (-45°~55° C)
(On): powered, aligned properly*
(Flashing): beam is broken or unaligned*
(Off): no power*
*Depending upon how programmed
IP65 / A1 alloy
Included

Specifications:

Standby -- 12~24VDC
Active -- 12~24VDC
Dimensions
Response time
Maximum Range
Detection method
Output
Operating temperature
Attenuation LED

Enclosure / Case
Mounting bracket

CurtainSensor1206.pmd

WARRANTY:

 

 

This SECO-LARM product is warranted against defects in material and workmanship while used in

normal service for a period of one (1) year from the date of sale to the original consumer customer.  SECO-LARM’s obligation is

limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair,

or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such

equipment is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at

SECO-LARM’s option.   In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal

or property damages of any kind to the purchaser or anyone else.

NOTICE

The information and specifications printed in this manual are current at the time of publication.  However, the SECO-LARM policy is one

of continual development and improvement.  For this reason, SECO-LARM reserves the right to change specifications without notice.

SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2007 SECO-LARM U.S.A., Inc.  All rights reserved.  This material may not be reproduced or copied, in whole or in part,

without the written permission of SECO-LARM

.

SECO-LARM

SECO-LARM

SECO-LARM

SECO-LARM

SECO-LARM

®

 U.S.A., Inc.

 U.S.A., Inc.

 U.S.A., Inc.

 U.S.A., Inc.

 U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA  92606

Tel: 800-662-0800 / 949-261-2999   Fax: 949-261-7326

Website: www.seco-larm.com

E-mail: [email protected]

Содержание E-9622-4B25

Страница 1: ...original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM...

Страница 2: ...turns ON Receiver LED never turns ON Receiver LED does not turn ON unless the sensor is triggered Receiver LED flashes all the time Does not trigger when beam is broken Receiver continuously triggers the alarm False alarm Table 3 Troubleshooting Table of Contents What s Included 2 Typical Installations Fig 1 2 Features 3 Choosing a Location 3 Beware Natural Interference Fig 2 3 Orientation to Sun ...

Страница 3: ...r upon simultaneous breaking of any single or 2 adjacent beams Rugged aluminum construction Anti tamper circuit for use when power is cut or end cap is removed No synchronizing wires required N O N C relay output LED alignment indicator L brackets and mounting hardware included Important Do not connect to power until the sensor is completely installed and the installation has been double checked I...

Страница 4: ...nsiderations Connecting the Wires 1 Receiver a Pull the end cap with the red wire leads off the receiver and slide the printed circuit board out far enough to expose the wiring block b Run the four wires or six wires if connecting the transmitter s power wires to the receiver through one or more of the three round knockout holes in the end cap near where the tamper button wires run and connect the...

Отзывы: