Enertech EAV Series Скачать руководство пользователя страница 37

Страница: 37 / 104

Enertech Global

EAV - EME/EMD Rev. A Models

Installation and Operations Manual

HYDRAULIC

SEPARATOR

SYSTEM

PUMP

MAKE-UP

WATER

NOTES 1,2

TEE SPACING NOT

TO EXCEED 4 PIPE

DIAMETERS OR 12”

BOILER

(NOTES 3,4)

BOILER

PUMP

(NOTE 6)

AUTOMATIC

AIR VENT

3-WAY FLUSH

VALVE

PRESSURE

RELIEF VALVE

PRESSURE

GAUGE

ΔP

LEGEND

WYE STRAINER

ACTUATED

ZONE VALVE

PRESSURE

REDUCING VLV

BACK-FLOW

PREVENTER

AIR ELIMINATOR

DIF. PRESSURE

BYPASS VALVE

ISOLATION BALL

VALVE

BOILER DRAIN

GRAY SHADED AREA IS OPTIONAL BOILER PIPING

NOTES:

1. IF BOILER DOES NOT HAVE INTERNAL TEMPERATURE CONTROL, AN EXTERNAL AQUASTAT IS REQUIRED AS A

HIGH LIMIT TO AVOID SENDING WATER TOO HOT FOR THE PEX PIPING.

2. INSTALL BOILER AT LEAST 10 FT. FROM CLOSELY SPACED TEES TO HELP AVOID TEMPERATURE MIGRATION.

3. BOILER MUST BE A CONDENSING TYPE. NON-CONDENSING BOILERS SHOULD NOT BE USED.

4. MAX BOILER SUPPLY NOT TO EXCEED 135 DEG F.

5. IF COMBI BOILER IS USED, THE “HOT ” OUTLET AT THE TURBOMAX WATER SHOULD BE CONNECTED TO THE

BOILER DHW “COLD” CONNECTION. THE BOILER DHW “HOT” CONNECTION SUPPLIES DHW TO THE HOME.

IF BOILER IS NOT COMBI TYPE, THESE CONNECTIONS WOULD NOT BE USED. IF BOILER IS NOT COMBI TYPE,

AN ELECTRIC OR GAS WATER HEATER SHOULD BE PIPED IN SERIES WITH THE TURBOMAX TANK, AS SHOWN

IN THE PREVIOUS DRAWING.

6. BOILER MAY HAVE INTERNAL PUMP (EXTERNAL PUMP SHOWN).

7. BOILER MANUFACTURER REQUIREMENTS AND LOCAL CODE REQUIREMENTS SUPERCEDE ANY

RECOMMENDATIONS IN THIS DOCUMENT

NOTE 5

COLD

HOT

FROM TURBOMAX

“HOT” CONNECTION

TO HOME

Figure 12d: Piping Diagram - Indoor Module with Backup Boiler

Notes:

If boiler does not have internal temperature control, an external aquastat is required as a high limit to avoid sending water too

hot for the pex piping.

Install boiler at least 10 ft. from closely spaced tees to help avoid temperature migration.

Boiler must be a condensing type. Non-condensing boilers should not be used.

Max boiler supply not to exceed 135 deg. F.

If combi boiler is used, the “hot” outlet at the TurboMax water should be connected to the boiler DHW “COLD” connection. The

boiler DHW “HOT” connection supplies DHW to the home. If boiler is not combi type, these connections would not be used.

If boiler is not combi type, an electric or gas water heater should be piped in series with the TurboMax tank, as shown in the

previous drawing.

Boiler may have internal pump (external pump shown).

Boiler manufacturer requirements and local code requirements supercede any recommendations in this document.

Piping Diagram - Indoor Module with Backup Boiler

Section 6: Unit Piping Installation

BACKUP ELECTRIC OR

GAS WATER HEATER

(STRONGLY

RECOMMENDED

FOR RESIDENTIAL

APPLICATIONS)

Содержание EAV Series









































































































Результаты поиска

Содержание EAV Series

Отзывы:

Похожие инструкции для EAV Series

Бренды по названию

Популярные бренды

Enertech EAV Series, Руководство по установке и эксплуатации

Результаты поиска

Содержание EAV Series

Отзывы:

Похожие инструкции для EAV Series

Бренды по названию

Популярные бренды