Energyficient Q-Box Скачать руководство пользователя страница 1

Q-Box

Instruction Manual

[email protected] | energyficient.com | 800-713-3732

1

IMPORTANT SAFETY INSTRUCTIONS

Q-Box should be installed by a qualified, licensed electrician. Modifying the product or altering the product 
voids UL Certification Listing. Failure to follow these instructions could result in death, bodily injury, fire, or 
electrical shock. 

• 

Wet location rated only when cover is closed

• 

For use only on walls or ceilings

• 

Not inteded for use with ceiling fans or other heavy/large fixtures

• 

Q-Hub ETL Listed, Conforms to UL Std. 5A, Certified to CAN/CSA C22.2 #62.1

Q-Box

Revealing a better way

Tools Needed for Installation:  

1/4” Nut driver, Small flat blade screwdriver

1. 

Ensure bonded washer is present on supplied screw.

2. 

Position Q-Hub onto mounting surface.

3. 

Secure Q-Hub to mounting surface by running supplied screw in 
until bonded washer is compressed and makes a watertight seal.

4. 

Ensure screw is properly seated to make a watertight seal as shown 
in Figure 1. 

5. 

If desired, a second screw can be used in alternate boss that is 
provided inside junction box. When using a second screw, ensure 
watertight seal is made either by adding silicone (or equal) or using 
screw with bonded rubber washer.

6. 

If pre-installed mounting screw is removed from box to use 
outboard mounting, seal hole in box with appropriate material, such 
as silicone, to ensure a watertight seal. 

WARNINGS

• 

Must use supplied mounting screw (#9-15x2”, 1/4” Hi-hex w/shoulder & 
EPDM bonded washer, Type S, Shield Coated) or equivalent. 

• 

If using any other screw type, care must be taken to seal around screw 
head in interior of junction box with an appropriate sealant to ensure a 
watertight seal. 

• 

Failure to follow these instructions voids wet location rating of junction 
box and may damage wires.

Inboard Mounting

NOTE: 

Q-Hub must be attached to a structural part of the building, 

such as a rafter

MOUNTING THE Q-HUB

Outboard Mounting

NOTE: 

Outboard mounting screws are not provided. Q-Hub must be 

attached to a structural part of the building, such as a rafter

1. 

Position Q-Hub onto mounting 
surface.

2. 

Secure Q-Hub to mounting 
surface using locations provided 
on Q-Hub as shown in Figure 2. 

3. 

It is recommended to use 
an appropriate screw for the 
environment, with a shoulder 
large enough to avoid any slip 
through the mounting locations. 

Figure 2 - Outboard  
Mounting Locations

Q-Box ships with mounting  

screw pre-installed

Mounting screw properly installed

Figure 1 - Inboard Mounting

1. 

Remove cover from the Q-Hub 
by placing a screwdriver into the 
slot of the locking mechanism 
and prying the cover counter-
clockwise until released from the 
lock. Figure 4

Removing Cover

Figure 4 - Pry cover counter-

clockwise to unlock

1. 

Verify O-ring is in place and secured in gasket groove in Q-Hub. An 
O-ring that is removed and/or not properly secured in groove may 
cause water ingress inside Q-Hub. 

2. 

Make sure O-ring is free from any debris, as this can compromise 
proper compression of the O-ring, resulting in a leak point. 

3. 

Position cover so alignment arrows line up. Alignment arrows are 
located on cover, directly to the left of locking hole in Q-Hub. 
The cover should seat completely into Q-Hub when lined up as 
described. 

4. 

Lock cover into place by turning cover clockwise until a click is 
heard from cover locking into place. You should feel and hear cover 
lock into place. Verify cover is locked into place. Figure 3 

Attaching Cover

Figure 3 - Attaching Cover

O-ring in place & 

secure

Align arrows

Turn cover clockwise 

until locked in place

Отзывы: