background image

May 2008 Rev. 11 

FOR YOUR SAFETY 

The use and storage of gasoline or other flammable vapors and liquids in open containers in the 
vicinity of this appliance is hazardous. 

Standard and Modular Direct Fired Heaters

Installation, Operation, and Maintenance Manual

Modular Direct Fired Heater 

     Standard Direct Fired Heater     

 

 

 

 

 

 

Direct Fired Module

 

 

 

 

 
Save these instructions

.  This document is the property of the owner of this equipment and is 

required for future maintenance.  Leave this document with the owner when installation or 
service is complete.   

 

RECEIVING AND INSPECTION 

Upon receiving unit, check for any interior and exterior damage, and if found, report it 
immediately to the carrier.  Also check that all accessory items are accounted for and are 
damage free.  Turn the blower wheel by hand to verify free rotation and check the damper (if 
supplied) for free operation.    

WARNING!!

 

Improper installation, adjustment, alteration, service or maintenance can cause property 
damage, injury or death.  Read the installation, operating and maintenance instructions 
thoroughly before installing or servicing this equipment.  ALWAYS disconnect power and gas 
prior to working on heater.

 

FOR YOUR SAFETY 

If you smell gas: 
1. Open 

windows. 

2. 

Don’t touch electrical switches. 

3. 

Extinguish any open flames. 

4. 

Immediately call your gas supplier. 

Содержание MR212





























Отзывы: