BATTERY INSTALLATION
Puck: To open, twist back cover of puck light counterclockwise and
remove. Insert 3 AAA batteries per puck (noting polarity). To close,
replace cover and twist clockwise.
IMPORTANT: Different types of batteries or new and used batteries
should not be mixed. Exhausted batteries should be removed from
the fixture and disposed of properly.
Remote:
To replace exhausted battery, remove the screw and
battery cover, on the back of the remote
. Insert 1 CR2032 battery,
noting polarity. Replace the cover and screw back in.
Note: Remove battery isolation tab before first time use.
MOUNTING INSTRUCTIONS:
1. Remove battery cover and use pre-
installed double-sided tape to mount in
desired location.
Note: For a more permanent
installation, screw through the two
holes using counter sunk screws.
Note: Ensure one of the two wireless
icons ( ) remains unobstructed and facing desired direction for
remote to reach interior sensor. The remote will work better with
direct line of sight access to the wireless icons ( ).
2. Reattach light to mounted battery cover by aligning tabs and
twisting clockwise.
Note: Battery door may remain mounted when changing batteries.
REMOTE OPERATION:
1. On the remote, press the
ON button to turn the lights on, or press
the
OFF button to turn them off. The default setting is white.
2. Pressing the
FADE button will slowly cycle through the spectrum of
colors. Press again to stop on the current color.
3. Press the
WHITE button to switch the lights back to white.
Screw holes
4. Use the
+ and - buttons to brighten or dim the lights.
5. The
R, G and B buttons stand for red, green and blue. These buttons
allow you to either select one of these colors or blend them to select
the desired color.
a. Hold the
R, G or B button for three seconds to go directly to
that color.
b. Press and release the buttons
repeatedly to move through the RGB
spectrum one color at a time.
c. Press and release the
R, G and B
buttons in any combination to create
custom colors.
6. The
SAVE button allows you to quickly
return to your favorite color. Once the
desired color is found, hold the
SAVE
button until the pucklight flashes. The color
will now be easily selectable by pressing
the
SAVE button. Once the color is set, you
can turn off the product and hit
SAVE to
turn it back on to the set color.
7. The
10min, 30min, 60min and 120min
buttons automatically turn the lights off
after the number of minutes indicated on
the button.
Note: When using the remote, point directly at the puck for proper
connection.
MANUAL OPERATION:
1. First press: turns the light on
in white
2. Second press: color-changing mode
3. Third press: stops on the current color
4. Fourth press: turns the light off
Functional range may be adversely affected by one or more of the
following factors: weather, radio frequency interference, low battery
or obstructions between the transmitter and receiver.
Wireless Color-Changing Puck Lights
50014 EnSp Manual v1
06/10/2020
©2020 Energizer. Energizer and certain graphic designs are
trademarks of Energizer Brands, LLC and related subsidiaries
and are used under license by Jasco Products Company, LLC. All
other brand names are trademarks of their respective owners.
Neither Jasco Products Company, LLC nor Energizer Brands, LLC
is affiliated with the respective owners of their trademarks.
Contact our U.S.-based Consumer Care at 1-800-654-8483
between 7AM-8PM CST.
90-day warranty. Visit www.byjasco.com for warranty details.
MADE IN CHINA/HECHO EN CHINA
READ IT
OR WATCH IT
R
ead
instRuctions
oR
watch
easy
-
to
-
follow
video
.
s
can
QR
code
oR
visit
http
://
bit
.
ly
/3
atk
y
kh
